Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Grapevine, TX
Gate access control in Grapevine usually starts with a keypad, a card reader, or a phone-entry system that no longer talks to the motor it’s wired to, and the fix is often smaller than replacing the whole setup. We service the full range: keypad entry, remote controls, phone entry, card readers, and video intercoms, across a city where the housing stock runs from 1890s cottages near Historic Downtown to 1990s HOAs in Silverlake. Call (817) 510-4183 and a live person answers, day or night.
Why Grapevine Homes Are Different
Grapevine sits on Blackland Prairie-adjacent clay, and that single fact explains most of what we see on gate service calls here. The soil heaves with rain and drought cycles, tilting gate posts enough to bind operators and derail slide-gate rollers. A post that was plumb in March can be an inch out by August, and an inch is enough to trip a limit switch or burn a gearbox. The February 2021 ice storm did its own damage, snapping hydraulic lines and shorting motor wiring all over town, and spring thunderstorms still take out hinges on larger swing gates with straight-line wind.
Then there’s the housing stock. Near Historic Downtown, gates from the early 1900s hang on masonry columns that have settled for a century; the original ornamental iron is worth keeping, but its hardware is often worn past tolerance. Out in Silverlake and Stone Bridge Estates, HOAs standardized wrought-iron driveway gates in the 1990s and early 2000s, and those gates are now twenty to twenty-five years into clay-soil movement. We do more post realignment and operator resets in those subdivisions than anywhere else in Grapevine.
The airport corridor along SH-114 and SH-121 adds a commercial layer no neighboring city matches. Hotel access lanes, rental-car facility lots, and cargo buildings run a hundred-plus gate cycles a day, which is why their gearboxes and loop detectors fail in three to five years instead of ten to fifteen. Grapevine technicians need to be fluent in industrial slide-gate operators and access-control integrations, and we are.
Our Main Grapevine Services
Most Grapevine homeowners call us first about one of these three jobs: a gate that stopped moving, a gate they’re replacing, or a motor that quit. Here’s what each involves in this city.
Gate Repair in Grapevine
Repair work in Grapevine is usually about clay movement and weather. A post shifts, a hinge binds, an operator fights the load and loses. We find what moved, set it back, and photograph the final position so the next technician doesn’t start from zero. Gate Repair in Grapevine walks through the common failure modes and what they cost to fix.
Gate Installation in Grapevine
New gate work here runs from replacing a rotted Historic Downtown side gate to full driveway automation in an HOA neighborhood with architectural standards. We pull the permit questions, match the existing ironwork where that matters, and spec posts for clay movement before we order anything. Gate Installation in Grapevine covers the full scope and pricing.
Gate Motor & Opener in Grapevine
When a motor quits, the question is whether the motor failed or the post movement killed it. In Grapevine the answer is often both: clay heave pushes the gate out of alignment, the motor strains for months, then burns out. We diagnose which came first before recommending replacement or repair. Gate Motor & Opener in Grapevine has the details.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Grapevine
Gate access control in Grapevine means the keypad, card reader, phone system, or video intercom that decides who gets through. On the airport corridor it’s industrial, with card readers at cargo buildings and phone entry at rental-car lots; in residential Grapevine it’s more often a keypad on an HOA gate or a video intercom at a driveway. Most calls come in after a storm or a power surge, when a board, a relay, or a loop detector stops talking to the operator. This page covers the residential and light-commercial side; the full breakdown lives on our Gate Access Control hub.
Keypad Entry
Signs you need it
Codes no longer work after a power surge, the keypad lights but won’t fire the motor, or the buttons need force to register.
What it costs in Grapevine
Replacing a standard keypad in Grapevine typically runs $225 to $400 installed, depending on brand and whether new wire pulls are needed.
How we do it
We test the wiring at both ends, replace the keypad or the damaged wire, program codes, and hand you a written record of the new code list and the part number.
Card Reader
Signs you need it
A card that worked Monday is dead Tuesday, the reader beeps but won’t release, or the system intermittently rejects good credentials at an HOA or commercial entry.
What it costs in Grapevine
Card reader replacement and reprogramming in Grapevine typically runs $275 to $450 per reader, plus any new cable runs.
How we do it
We check the reader against the control board, confirm the credential format, swap the reader or repair the wiring, and re-enroll test cards before we leave.
What Gate Access Control Costs in Grapevine
| Item | Typical range in Grapevine |
|---|---|
| Keypad replacement | $225-$400 |
| Card reader replacement | $275-$450 |
| Access control board repair | $250-$500 |
Does a power surge wipe out gate access control in Grapevine?
Yes, and we see it after every spring storm season. A surge takes out the control board, the keypad, or the loop detector. The fix is usually a board swap and re-programming, not a full system replacement.
Will a Grapevine HOA require a specific access control format?
Most do. HOA gates in Silverlake and Stone Bridge Estates often run on a specific card or fob format, and swapping hardware without matching it locks residents out. We check the HOA spec before quoting.
Gate Parts & Welding in Grapevine
Gate parts and welding in Grapevine is where clay movement shows up physically: hinges snapped, posts leaning, rails bowed, rollers ground flat. On older homes near Historic Downtown the original ironwork is often worth keeping, and we’d rather weld and reinforce than replace. Out in the 1990s subdivisions, post replacement is the regular job. See the full scope on our Gate Parts & Welding hub.
Hinge Replacement
Signs you need it
The gate drags or sags on one corner, oiling no longer helps, or you can see a crack at the hinge weld.
What it costs in Grapevine
Replacing a pair of heavy swing-gate hinges in Grapevine typically runs $180 to $335, depending on gate weight and accessibility.
How we do it
We support the gate, cut or unbolt the old hinges, weld or bolt on new ones, and set the gate back to plumb.
Post Replacement
Signs you need it
The post leans visibly, the gate binds at the latch or the top, and you can rock the post with hand pressure.
What it costs in Grapevine
Residential gate post replacement in Grapevine typically runs $350 to $700 per post, including concrete and finish work.
How we do it
We dig out the old footer, set a new post in concrete at proper depth for clay movement, and re-hang the gate square.
What Gate Parts & Welding Costs in Grapevine
| Item | Typical range in Grapevine |
|---|---|
| Hinge replacement (pair) | $180-$335 |
| Post replacement (per post) | $350-$700 |
| Rail repair or welding | $150-$400 |
Can you weld ornamental iron without ruining the finish?
Generally yes. We weld the repair, grind it clean, and match the paint or finish as closely as the existing surface allows. On century-old gates we document the original finish before touching anything.
My HOA wants the post replaced but I think it can be reset. Can you tell me which is right?
We can, and we’ll show you. If the post is structurally sound but leaning, we reset it. If it’s rusted through at ground level, replacement is the only fix. We photograph what we found.
Brands We Service in Grapevine
We work on DoorKing, Elite, Mighty Mule, and LiftMaster equipment already on Grapevine properties, plus the other major automation brands. Common boards and standard parts are stocked in our metro-area trucks; specialty parts are ordered next-day. Our brands page lists what we service.
Pricing for Gate Repair in Grapevine, TX
| Service | Typical range in Grapevine |
|---|---|
| Keypad replacement | $225-$400 |
| Card reader replacement | $275-$450 |
| Access control board repair | $250-$500 |
| Hinge replacement (pair) | $180-$335 |
| Post replacement (per post) | $350-$700 |
| Rail repair or welding | $150-$400 |
| Gate roller replacement | $120-$250 |
| Welded custom bracket or brace | $100-$300 |
Prices in Grapevine push toward the top of a range when clay movement has distorted the gate beyond simple adjustment, when HOA standards require specific finishes, or when the existing wiring is damaged and needs new pulls. Whatever the number, it’s written down and handed to you before anyone picks up a tool.
Neighborhoods We Serve in Grapevine
We cover all of Grapevine, including these neighborhoods where we work regularly. Response time across the area is usually same-day or next-morning for repair calls.
- Historic Downtown Grapevine
- Silverlake
- Stone Bridge Estates
- Cross Timbers
- Timberline Estates
Service Area - Cities Near Grapevine
Besides Grapevine itself, our gate technicians cover the surrounding Tarrant County corridor on a regular schedule. We handle repair, motor, and access-control calls in Southlake, TX, Colleyville, TX, Euless, TX, and Coppell, TX with the same written-price rule.
Serving Grapevine, TX - Our Local Coverage Area
We’re based in the Grapevine area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Grapevine
Sometimes, and it depends on the neighborhood. In Silverlake and Stone Bridge Estates, visible changes like a new gate or different operator usually need HOA approval. Straight repairs of existing equipment generally don’t. We’ll tell you which category your job falls into before we quote.
For a gate stuck open or shut, a technician can usually reach you same day. We dispatch from our Dallas-Fort Worth office, and Grapevine is a regular coverage area. The phone is answered live 24 hours, so you’ll know your slot the moment you call.
We won’t blindly match it, but we’ll read it. Bring any other company’s written estimate and we’ll review it at no charge, point out what it covers and what it doesn’t, and hand you our own written price. You decide with both numbers in front of you.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Grapevine Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.