Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Bedford, TX
Gate access control in Bedford usually means retrofitting a keypad, card reader, or phone entry system onto a gate that was hung in the 1970s or 1980s. The housing stock here predates modern automation, so the wiring, the post condition, and the gate’s swing arc all have to be assessed before any control equipment gets mounted. Call (817) 510-4183 and we’ll put the price in writing before any work starts.
Why Bedford Homes Are Different
Bedford’s residential build-out peaked between roughly 1972 and 1995, and most of those homes still have their original wood privacy fences, 4×4 treated-pine posts, and swing gates. That means a large share of the gate hardware in this city is now 35 to 50 years old. The bigger problem sits under the surface. Bedford sits on Blackland Prairie clay, which expands dramatically when wet and shrinks when dry. Gates that were hung square in June are binding by September. Posts that looked solid in the winter are leaning after the spring rains. In the older neighborhoods around Forest Ridge and Central Park, we regularly find original posts set in shallow footings that the clay has partially ejected. The gate didn’t fail because the hinges wore out. The ground moved under it. Many Bedford subdivisions also fall under HOA covenants that restrict gate materials and finishes, so a repair has to match the approved style rather than swapping in whatever hardware is cheapest.
Our Main Bedford Services
Most Bedford calls start with one of three problems: a gate that won’t swing, a gate that needs to be replaced entirely, or a motor that stopped doing its job. Each has its own Bedford page with local pricing and details.
Gate Repair in Bedford
A sagging wood gate on a 1980s post, an ornamental iron gate with a cracked weld, a latch that no longer lines up after a wet season. Those are the repairs we see most in Bedford, and the fix often requires addressing the post footing, not just the hinge. We write the price before we start, and we document what we found and what we set before we leave. Gate Repair in Bedford
Gate Installation in Bedford
When a Bedford gate has rotted past repair or an HOA requires a specific style, installation is the better path. We set new posts in deeper bell-bottom footings so the clay has less to grab onto when it heaves, and we match finishes and materials to what the neighborhood already has. Gate Installation in Bedford
Gate Motor & Opener in Bedford
Bedford’s thermal swings, from 100-degree summers to hard freezes, are hard on gate motors and control boards. A motor that worked for a decade can fail after one particularly violent hail season or a series of freeze-thaw cycles. We service nine automation brands, so the motor already on the property is usually the one we repair. Gate Motor & Opener in Bedford
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Bedford
Gate access control in Bedford usually means adding a keypad, card reader, phone entry system, or video intercom to a gate that was built decades before those systems existed. The challenge here is the housing era: a 1978 gate post set in shallow clay was never designed to carry the conduit, wiring, and mounting hardware that access control requires. That’s why our Gate Access Control work in Bedford starts with the post and the swing arc, not the keypad.
Keypad Entry
Signs you need it
A keypad that blinks but won’t release the gate, or codes that work intermittently after rain, usually means water intrusion or a failing relay, common in Bedford’s humid summers.
What it costs in Bedford
Keypad entry work in Bedford typically runs $225 to $650 depending on whether we’re replacing the keypad, the control board, or both and pulling new wire through an old post.
How we do it
We test continuity at the keypad and the board, replace what failed, seal the housing against moisture, program the codes, and photograph the wiring before we close it up.
Phone Entry
Signs you need it
A phone entry system that won’t dial out or a guest call that rings once and drops usually points to a dying GSM module or a corroded terminal block.
What it costs in Bedford
Phone entry repairs in Bedford generally run $300 to $900, with full unit replacement on the higher end when the board has been cooked by a Texas summer.
How we do it
We check the power supply first, test the dial-out circuit, replace the module or board, and leave a photo record of the new configuration and the programming steps.
What Gate Access Control Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Keypad entry repair or replacement | $225 - $650 |
| Phone entry system repair | $300 - $900 |
| Card reader or video intercom installation | $14 - $112 per hour |
Can you add a keypad to an old Bedford gate post?
Usually yes. If the post is solid at the base and hasn’t been heaved out by the clay, we can run new conduit and mount the keypad on a weatherproof backplate. If the post is rotted, we reset it first.
Will my HOA need to approve the access control equipment?
Many Bedford HOAs require that any visible gate hardware match the approved style and finish. We can mount equipment discreetly and provide written specs for the HOA before the work is scheduled. Call (817) 510-4183 for a written quote.
Gate Parts & Welding in Bedford
Gate parts and welding in Bedford usually means hinge replacement, post replacement, rail repair, or cracking a weld on ornamental iron that’s been stressed by the clay heave cycle. The defining pattern here is a gate that has shifted out of square within a single wet season because the 1970s or 1980s post underneath it has started to move. Our Gate Parts & Welding work treats the post and the hinge as one system, not two separate fixes.
Hinge Replacement
Signs you need it
A gate that drags on the latch side or leaves a fresh scrape mark on the concrete after every rain usually means the hinge pin is worn and the leaf has started to sag.
What it costs in Bedford
Hinge replacement in Bedford typically runs $180 to $450 depending on the gate’s weight and whether the post face needs reinforcement before new hardware goes on.
How we do it
We block the gate level, cut or unbolt the old hinges, verify the post with a level, install heavier-gauge hinges, and photograph the final alignment.
Post Replacement
Signs you need it
A post that has visibly pulled away from the gate or leans a few degrees after the rainy season has often been ejected by the clay and needs a deeper footing, not just a shim.
What it costs in Bedford
Post replacement in Bedford generally runs $350 to $800 per post, including a bell-bottom footing dug below the clay’s movement line and new concrete.
How we do it
We pull the old post and footing, drill or auger a deeper hole with a wider base, set the new post in fresh concrete, and re-hang the gate after the cure.
What Gate Parts & Welding Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Hinge replacement | $180 - $450 |
| Post replacement (per post) | $350 - $800 |
| Custom welding repair | $120 - $405 |
Can you weld a crack in an ornamental iron gate without removing it?
Yes, in most cases we can grind the crack site, weld it in place, and touch up the finish to match the existing coating. If the crack is at a hinge point, the hinge may need to come off first for a clean repair.
Is it worth replacing a rotted wood post, or should we replace the whole gate?
If the gate itself is solid and square, post replacement is the better value. In Bedford’s clay, we reset the post in a deeper bell-bottom footing so the same failure doesn’t repeat after the next rainy season. Call (817) 510-4183 for a written estimate.
Brands We Service in Bedford
We work on FAAC, BFT, Linear, and Viking automation, plus five other major brands. We carry the common control boards, limit switches, and receiver modules for these units on the truck, so most Bedford motor repairs don’t wait on a parts order. Our brands page lists the full lineup.
Pricing for Gate Repair in Bedford, TX
| Service | Typical range in Bedford |
|---|---|
| Gate repair (per visit, parts excluded) | $14 - $112 per hour |
| Emergency gate repair call-out | $14 - $112 per hour |
| Gate installation (full swing gate) | $14 - $112 per hour |
| Gate installation (full slide gate) | $14 - $112 per hour |
| Gate motor/opener repair | $14 - $112 per hour |
| Gate motor/opener installation | $1,000 - $1,800 |
| Keypad entry repair or replacement | $225 - $650 |
| Phone entry system repair | $300 - $900 |
| Hinge replacement | $180 - $450 |
| Post replacement (per post) | $350 - $800 |
| Custom welding repair | $120 - $405 |
In Bedford, two things push the price up: clay-expanded posts that need a deeper footing, and HOA finish matching on visible hardware. Whatever the figure, we hand you the written price before any work starts, and that number doesn’t change unless you approve a change in scope.
Neighborhoods We Serve in Bedford
We work across Bedford from the older subdivisions near Forest Ridge and Central Park to the newer streets further out. Response time across the city is typically same-day for emergency gate failures, and next-day for scheduled service.
- Forest Ridge
- Central Park
- Woodland Hills
- Bedford Meadows
- Shady Brook
Service Area - Cities Near Bedford
We also serve the surrounding cities where the same clay soil and housing era shape the work. Visit our pages for Colleyville, TX, Euless, TX, Hurst, TX, and Grapevine, TX.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bedford
Same day in most of Bedford. If a gate is stuck open or won’t secure, call (817) 510-4183 and a live person answers, day or night. We dispatch from the Dallas-Fort Worth office with crews serving Bedford locally.
If the repair uses the same material and finish as the existing gate, most Bedford HOAs don’t require formal approval. If the repair changes the appearance or hardware style, we can provide written specs and photos for the HOA before work begins.
Yes. We match wood species, stain, and hardware, or match the iron profile and finish on ornamental work. In HOA-governed neighborhoods, we photograph the existing conditions and keep the replacement consistent with the approved look.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bedford Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.