Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLock Repair in Irving, TX
Lock repair for residential gates in Irving, TX, typically ranges from $150 to $350, depending on whether the issue stems from a simple solenoid adjustment, a misaligned strike plate, or a failed magnetic lock controller. Most repairs are completed during the initial visit, and we provide a written price before any technician picks up a tool. If your gate fails to latch, remains locked when it should open, or makes a buzzing sound without retracting the pin, you likely need a professional gate repair assessment to prevent further damage to the gate motor. Call (817) 510-4183 to schedule a visit, and we will provide an upfront, written estimate for the repair.
At Vance Gate Repair Irving, we treat every gate as a piece of commercial infrastructure, regardless of whether it secures a private driveway in Las Colinas or a light commercial lot near the airport. We founded our business in 2014 on the principle that property owners deserve documented evidence of what they are paying for. When you choose us for your Gate Repair in Irving, you receive a full photo record of the parts we installed, the adjustments we made, and the wiring changes performed. This is part of our commitment to The Haven Standard, ensuring you never pay twice to fix the same problem.
When You Need Lock Repair
Not every gate issue requires a full motor replacement. Often, the problem is isolated to the locking mechanism. We see these symptoms regularly across Irving, and they are usually mechanical or electrical in nature.
- The gate clicks but does not retract: This often points to a failed solenoid or a loose electrical connection. If the lock receives power but cannot physically move the pin, the internal coil may be burnt out.
- The latch fails to catch: Over time, thermal expansion in the North Texas heat can cause gate posts to shift slightly. If the latch and the strike plate are off by even a quarter-inch, the gate will swing past the closed position without engaging.
- Buzzing or humming sounds: A continuous buzzing coming from the lock housing usually indicates that the solenoid is struggling to pull the pin back, often due to internal friction or a lack of lubrication.
- The mag-lock does not hold: Magnetic locks depend on a clean, flush surface. If there is rust, debris, or a gap between the magnet and the armature plate, the holding force drops significantly, making the gate easy to push open.
- Manual override failure: If you cannot disengage the lock using your manual key during a power outage, the cylinder is likely seized due to corrosion or lack of use.
If you notice these signs, do not force the gate. Forcing a stuck lock can strip the gears in your gate motor or bend the mounting brackets. Call (817) 510-4183, and we will dispatch a technician to inspect the assembly.
Our Lock Repair Process
We operate under The Haven Standard, which dictates how we approach every call. We do not provide verbal estimates that change once we are on-site. Every job follows this structured workflow to ensure accuracy and transparency.
- Visual Inspection and Testing: We begin by testing the lock’s electrical signal and mechanical movement. We measure the voltage at the lock terminal to ensure the control board is sending the correct power.
- Written Scope and Price: Before we begin any work, we hand you a written document detailing exactly what is wrong and what it will cost to fix. We do not start until you approve this scope.
- Component Repair or Replacement: Whether we are servicing a FAAC, BFT, Linear, or Viking system, we use high-quality parts that match your specific motor. We clean the housing, adjust the alignment, and lubricate the moving parts.
- Verification and Documentation: Once the repair is complete, we photograph the new alignment, the part installed, and the final gate position. This photo record is left with you and filed in our job history for your future reference.
- 365-Day Done Right Promise: If the repair does not hold or if the same component fails within one year, we return to make it right at no additional charge. We stand by our work, and we put that promise in writing.
BeforeAfterLock Repair Pricing in Irving
We believe in upfront, transparent pricing. The cost of your repair depends on the type of lock system you have and the underlying cause of the failure. Below are the typical ranges for common lock-related services in Irving.
| Service Type | Estimated Range |
|---|---|
| Alignment and Strike Plate Adjustment | $150 – $225 |
| Solenoid or Latch Assembly Replacement | $250 – $450 |
| Magnetic Lock (Mag-Lock) Controller Repair | $275 – $500 |
| Manual Key Cylinder Replacement | $180 – $300 |
These prices include our diagnostic visit and the labor required to perform the repair. If we find that the issue is not the lock but a deeper problem with the home gate operator, we will document that finding and provide an updated price before proceeding. Call (817) 510-4183 for an exact quote on your specific gate system.
Safety and Professional Care
Electric gate repair for systems using magnetic locks or high-tension springs involves significant forces and electrical currents. We strongly advise against attempting to open the lock housing or adjust the solenoid if you are not trained in gate access control. High-voltage connections inside the control box can cause injury, and incorrect adjustments to the gate travel limits can cause the gate to crush or damage vehicles. Our technicians are background-checked and uniformed, and we arrive prepared to handle these systems safely. If your gate is currently stuck in a dangerous position, block the area to prevent accidental operation and call us immediately.
FAQs - Lock Repair
Can you fix my gate lock today?
We prioritize urgent automatic gate repair issues, and we often have availability for same-day or next-day service in Irving. When you call (817) 510-4183, we will check our current schedule and provide you with a firm arrival window. We do not use automated attendants, so you will speak directly with a person who can provide immediate assistance.
Do I need to replace the whole motor if the lock is broken?
Rarely. Most lock issues are isolated to the locking mechanism itself, such as a solenoid, a latch, or a controller. We specialize in weld & rust repair and other individual component fixes for brands like FAAC, BFT, Linear, and Viking, so you do not have to pay for a full operator replacement when a smaller repair will solve the problem. We only recommend replacement if the existing hardware is obsolete or beyond repair.
Is it cheaper to repair or replace the lock?
In most cases, repairing the existing lock is more cost-effective than replacing the entire assembly, especially when the gate operator itself is still functioning well. We will provide an honest assessment of the condition of your lock and give you the written price for both repair and replacement options, so you can make the decision that fits your budget. Call (817) 510-4183 for a free estimate on your options.
What if the lock breaks again next month?
Every repair we complete is backed by our 365-Day Done Right Promise. If the issue returns within one year, we will return to fix it at no additional cost to you. This is our guarantee, and it is documented on every invoice we provide. We do not believe in temporary fixes; we believe in doing the job correctly the first time.
Written by Adrian Vance, Owner at Vance Gate Repair Irving, serving Irving.