Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Dallas, TX
Gate access control in Dallas usually means one of two things: a standalone keypad on a residential driveway gate, or a full entry system on one of the older gated communities that run through Preston Hollow and Lake Highlands. What makes Dallas work different is the soil. Blackland Prairie clay expands and contracts enough to shift gate posts out of alignment, which pulls wiring connections loose and throws photo-eye sensors out of tolerance. That means access control problems here are frequently a foundation problem wearing an electronics costume. If your keypad stopped working after a wet spring or a long dry spell, call (817) 510-4183 and we’ll tell you what we think before we send anyone out.
Why Dallas Homes Are Different
Most of the automated gates we open up in North Dallas were installed with the house, which puts them at 20 to 40 years old. The ornamental wrought-iron gates in Preston Hollow and Devonshire were built well, but four decades of Texas sun and humidity take a toll on wiring jackets, control boards, and the small mechanical parts that live inside the operator housing. The February 2021 freeze left another layer of damage we still find: actuator housings with hairline cracks that let moisture in, and control boards that work fine for months and then fail on a humid morning.
The bigger factor is what’s under the gate. Dallas sits on shrink-swell clay that heaves with spring rain and contracts to deep cracks by August. A post that moves even a quarter inch changes the gap at the latch and throws off every sensor reading along the gate’s path. We check the post base on every access control call, because a keypad that eats the code and does nothing is often reading a gate that’s no longer where the system thinks it is.
Our Main Dallas Services
These are the three calls we run most often across Dallas. Each has its own page with local pricing and the specific failure modes we see in this market.
Gate Repair in Dallas
Most repair calls in Dallas fall into two buckets: the gate won’t open, or the gate won’t close and stay closed. Bent frames from spring wind events, worn rollers, cracked hinge welds, and operators that have lost their limit settings. We photograph what we find, write the price, and fix it the same visit in most cases. Full details on the Gate Repair in Dallas page, including what a typical spring replacement costs and how we handle post-tilting gates.
Gate Installation in Dallas
New gates in Dallas need to be engineered for the soil, not just welded square and set in a bag of Quikrete. We set posts below the active clay zone wherever possible and build for the wind loads that flatten cheap gate frames during storm season. If you’re replacing a gate or adding one to a new build, the Gate Installation in Dallas page walks through the process, the options, and what a written quote includes.
Gate Motor & Opener in Dallas
Operator failures in Dallas follow a pattern: heat and humidity kill the board, the freeze cracked the housing, or the motor’s been fighting a misaligned gate so long it burned itself out. We work on nine major automation brands and we’ll tell you if the motor can be repaired before anyone suggests replacing it. The Gate Motor & Opener in Dallas page covers what we stock, what we order, and what a typical replacement costs.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Dallas
Gate access control in Dallas is the collection of electronics that decides who gets in: keypads, remotes, phone entry, card readers, and video intercoms. In neighborhoods like Preston Hollow and the gated sections of Lake Highlands, these systems were often installed with the house 20 to 30 years ago and are now failing in ways that look intermittent, which makes them hard to diagnose. A system that works every morning but refuses the guest code at night is typically a wiring or alignment issue, not a bad keypad. This is the work Adrian Vance has been documenting since commercial access-control jobs in 2014, and every residential visit gets the same photographic record of what was found and what was changed. That’s the entire point of our Gate Access Control approach: written evidence, not a verbal summary.
Keypad Entry
Signs you need it
Your keypad works when the weather is mild but refuses codes after rain or a hot afternoon, or it accepts the code and the gate doesn’t move.
What it costs in Dallas
Keypad replacement in Dallas typically runs $280 to $650 depending on the model and whether the wiring run to the operator needs to be replaced too.
How we do it
We open the housing, check the seal and the wiring terminals, test the output at the operator end, and replace or rewire as needed, then photograph the final connections for your record.
Phone Entry
Signs you need it
The call rings and connects, but the gate doesn’t respond when the visitor code is entered, or the system works only from one carrier and not another.
What it costs in Dallas
A phone entry module or cellular unit runs $450 to $950 in Dallas, and that price includes programming the relay and testing from both a landline-style and cellular call if the system uses one.
How we do it
We identify the board type, check the relay output and phone line or cellular signal, replace the failed module, and document the programmed settings so any future technician has a starting point.
Video Intercom
Signs you need it
The video feed is dead but the call audio works, or the monitor inside the house shows the camera feed but the unlock button does nothing.
What it costs in Dallas
Video intercom repair in Dallas ranges from $350 for a camera or monitor swap to $1,100 when both ends and the cable run have failed.
How we do it
We test the camera, the monitor, and the wiring between them, replace only what failed, and leave you with a written record of every component we touched.
What Gate Access Control Costs in Dallas
| Item | Typical range in Dallas |
|---|---|
| Keypad replacement | $280 - $650 |
| Phone entry module | $450 - $950 |
| Video intercom repair | $350 - $1,100 |
Can you fix my access control if the gate post has moved?
Usually yes. We check post alignment first because a shifted post changes the latch gap and throws off every sensor reading. We fix the electronics after the geometry is stable, or the same problem returns within a season.
Will you work on the system I already have?
Yes. We service nine automation brands and the access control hardware that connects to them. We don’t push replacement when a board, relay, or keypad can be repaired and documented.
Gate Parts & Welding in Dallas
Gate parts and welding in Dallas are usually the same job wearing two hats: the post has shifted in the clay, the hinge has torn, or the rail has sagged, and the fix requires both a new part and a weld or a concrete repair. In Preston Hollow and the gated estates along Strait Lane, we routinely find posts that someone surface-poured concrete around instead of digging out the heaved clay, and that patch fails within one wet season. The welding work is the physical half of what our Gate Parts & Welding work covers, along with the rollers, hinges, and rail sections that wear out on Dallas gates every few years.
Hinge Replacement
Signs you need it
The gate sag is visible at the latch corner, the gate scrapes the driveway on the swing, or you see rust staining down from the hinge barrel.
What it costs in Dallas
Hinge replacement on a Dallas ornamental iron gate runs $180 to $420 per hinge, depending on the gate weight and whether the post plate needs to be re-welded too.
How we do it
We support the gate, cut or unbolt the old hinge, weld or bolt the new one in place, and check the swing arc before we leave.
Post Replacement
Signs you need it
The post leans visibly, the latch side gap opens and closes from week to week, or the gate drops when it’s released from the operator.
What it costs in Dallas
Post replacement in Dallas runs $680 to $1,500 per post, with the higher end covering a deeper set below the active clay and a longer cure time before the gate is hung.
How we do it
We cut the old post, dig through the active clay zone, set the new post in concrete below the heave line, and re-hang the gate after the footing has set.
Custom Welding
Signs you need it
You have a crack at a joint, a bend in the frame from a wind event, or a design change you want made to the existing gate rather than a full replacement.
What it costs in Dallas
Custom welding on a Dallas gate typically runs $150 to $475 depending on the number of joints, the material thickness, and whether an on-site or shop fixture is needed.
How we do it
We clean the area, grind a bevel where needed, weld and grind smooth, then primer and paint the repair to match as closely as the original finish allows.
What Gate Parts & Welding Costs in Dallas
| Item | Typical range in Dallas |
|---|---|
| Hinge replacement | $180 - $420 per hinge |
| Post replacement | $680 - $1,500 per post |
| Custom welding | $150 - $475 per job |
How do I know if my post can be straightened instead of replaced?
If the post is straight but leaning, it can sometimes be re-set. If it’s bowed or rusted at the base, replacement is the reliable fix. We’ll tell you which one applies and why, with photos.
Will the weld match my existing gate finish?
The weld itself is ground smooth and primed. We color-match the paint as closely as we can, but a weathered 30-year-old finish won’t match perfectly. The repair will be sound and protected.
Brands We Service in Dallas
We work on FAAC, BFT, Linear, and Viking operators that are common across Dallas gated entries, plus five other major automation brands. Parts for these systems are stocked locally or ordered same-week, and most access control jobs are one-visit repairs. See the full list on our brands page.
Pricing for Gate Repair in Dallas, TX
| Service | Typical range in Dallas |
|---|---|
| Gate access control diagnostic | $95 - $175 |
| Keypad replacement | $280 - $650 |
| Phone entry module | $450 - $950 |
| Video intercom repair | $350 - $1,100 |
| Gate parts: hinge replacement | $180 - $420 per hinge |
| Gate parts: post replacement | $680 - $1,500 per post |
| Custom welding | $150 - $475 per job |
| Roller or wheel replacement | $120 - $250 per wheel |
| Slide gate rail repair | $350 - $800 |
What pushes a Dallas quote up is usually what’s under the gate: a post that’s lost its footing in the clay and has to be re-set before any parts work can hold. Every price we give is written and handed over before work starts, no exceptions.
Neighborhoods We Serve in Dallas
We run calls across the whole Dallas area, from the older gated estates to the 1990s and 2000s master-planned communities where ornamental iron gates came standard. We’re typically on site within 24 to 48 hours depending on the day’s schedule.
- Preston Hollow
- Lake Highlands
- Devonshire
- Bluffview
- North Dallas
Service Area - Cities Near Dallas
Our technicians also run calls to the cities that border Dallas. If your property is just outside the city line, we’ll still likely be your closest option. We regularly serve Irving, TX, Grand Prairie, TX, Carrollton, TX, and Coppell, TX with the same written pricing and photo documentation.
Serving Dallas, TX - Our Local Coverage Area
We’re based in the Dallas area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Dallas
We answer the phone 24/7 and can usually be on site within 24 to 48 hours for non-emergency work. A gate that won’t close or secure is treated as a priority and we’ll tell you the honest ETA when you call, not a vague window.
If your gate fronts a shared entry or is in a managed community, check your governing documents first. For a private driveway gate on your own property, you don’t need anyone’s approval to have it repaired. We’re happy to provide a written quote for your HOA if one is requested.
No. The price we hand you before work starts is the price you pay. If we discover something hidden during the job, we stop and give you a new written figure before continuing. That’s Clause 1 of the Haven Standard, and we don’t work any other way.
Every job we do in Dallas starts with a written price and ends with a photo record of what we found and what we left behind. Call (817) 510-4183 for a free estimate on your gate access control or parts and welding work.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Dallas Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.