Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Repair in Irving, TX | Vance Gate Repair Irving
We provide independent Ghost Controls Gate Repair - Irving, and the work here looks different than it does fifteen minutes east. The reason is the soil. Irving sits on Blackland Prairie expansive clay that swells after rain and shrinks during drought, pulling gate posts out of square and dragging Ghost Controls limit switches out of calibration on a cycle that repeats every year. That means our Ghost Controls calls in Irving are rarely about the motor itself. They’re about what the ground did to the mounting. Call (817) 510-4183 for a written price before any work starts.
Why Irving Residents Choose Us for Ghost Controls Service
Vance Gate Repair is an independent Ghost Controls service provider. We are not manufacturer-affiliated and not an authorized dealer. What we are is the shop that pulls up with the OEM control board on the truck and a photo log of the last trip, so nobody has to pay twice to rediscover the same problem. Adrian Vance spent years running commercial access-control installation across metro job sites before relocating and has been on Irving service calls for over a decade, including steady work around the Las Colinas corridor where residential gates share hardware with commercial systems. That background shows up in how we document Ghost Controls repairs: wiring diagrams, limit-switch readings, part numbers, and photos of what we found, what we set, and what we installed.
Residents choose us because we name the price before anyone picks up a tool. That’s Haven Standard Clause 1: have it in writing. No verbal estimate, no call-for-a-quote, no invoice bigger than the number you saw at the start. We also keep genuine Ghost Controls parts on hand for the models Irving homeowners actually run, which shortens repair time on TDS2, AXD, and R20 systems.
Common Ghost Controls Gate Repair Problems We Solve in Irving
- Limit switch drift on clay-heaved gates. When Irving’s Blackland clay swells after spring rain, gate posts move. A Ghost Controls opener doesn’t know the geometry changed. It just drives the arm to where the limit switch says travel ends, and when that point no longer matches the actual gate position, the opener stalls mid-travel or slams the stop. We see this constantly on older North Irving ranch homes where gates were retrofitted onto footings poured decades before the opener existed. The fix is usually realignment and recalibration, not a new motor.
- Control board corrosion near Las Colinas drainage channels. Irving’s humidity swings plus the winter ice-melt exposure around drainage features off the Las Colinas corridor accelerate corrosion on Ghost Controls control boards. We open the housing and find green oxidation on the relay contacts or a swollen capacitor from moisture ingress. The board gets replaced with a genuine Ghost Controls unit, and we seal the housing properly so it doesn’t happen again inside eighteen months.
- Weld fatigue at the post bracket. Ghost Controls arms use a shorter geometry than some other brands, which concentrates torque at the post bracket when the gate isn’t perfectly square. On ornate iron swing gates in Las Colinas HOA subdivisions, that bracket weld cracks. We grind it out, re-weld, and reinforce the mounting plate so the next clay shift doesn’t snap it again.
- Battery backup failure after 100°F heat soaks. West-facing Irving installations bake in July and August. Ghost Controls battery backups sit inside the operator housing where ambient temperature climbs past 120°F on a hot afternoon. The batteries degrade early, and the first time a late-summer thunderstorm knocks out utility power, the gate is dead. We test battery voltage on every Ghost Controls visit and replace failing packs before they strand anyone.
- Remote and receiver sync loss after storms. Lightning-adjacent strikes and power surges across Irving’s grid knock Ghost Controls receivers off their programmed remote codes. The opener still works from the hardwired keypad, but every handheld remote goes dark. Reprogramming is quick, and we’ll add a surge suppressor at the outlet if the homeowner wants protection against the next storm season.
BeforeAfterGhost Controls Service in Irving: What Local Conditions Mean for Your Equipment
Here’s the thing most Ghost Controls pages won’t tell you because the writer has never stood on the soil. Irving sits squarely on Blackland Prairie expansive clay. That clay swells dramatically after rain and shrinks just as dramatically during drought. The result is that we see the same Ghost Controls openers in Las Colinas HOA subdivisions need post re-shimming and limit switch recalibration every 12 to 18 months. Identical systems fifteen minutes east in Farmers Branch, sitting on sandy loam, almost never shift. If you own a Ghost Controls opener in Irving, the ground under your gate is a standing repair condition. We plan for it. We photograph post positions, record limit-switch settings, and leave you a written note of what the ground did and what we corrected, so when it recurs next season you’re not starting from zero. Name what you found. Name what it costs. Name what you left behind. That’s how we run every Ghost Controls job in this city.
Ghost Controls Models & Products We Service in Irving
Our techs work on the full Ghost Controls residential line that shows up in Irving: the TDS2 heavy-duty swing gate opener, the AXD dual automatic gate opener, the R20 residential slide gate opener, and the VEHICLE sensor and accessory line. We stock genuine Ghost Controls control boards, arms, remotes, and limit assemblies for these models locally so an Irving service call doesn’t wait on a warehouse halfway across the country. When a genuine Ghost Controls arm is discontinued and the gate’s geometry demands a taller post bracket, we’ll switch to a proven aftermarket actuator and document exactly what we installed and why. For Irving’s recurring frame shifts, we usually recommend reinforcing the mounting post and replacing the limit assembly rather than swapping the entire opener. Repair beats replacement when the opener itself is still sound. We also stock parts and service coverage through our Ghost Controls sales & service division, so the same tech who diagnoses your TDS2 can also source the correct replacement part without a second trip.
Ghost Controls Service Pricing in Irving
Most Ghost Controls repair calls in Irving land between $180 and $340 when the problem is limit switch recalibration, remote programming, or a receiver sync issue. Control board replacement runs $260 to $480 depending on the model and whether we’re installing a genuine Ghost Controls board or an aftermarket equivalent. Full actuator or arm replacement on a TDS2 or AXD system typically falls between $450 and $700 when the post bracket is intact. What drives the cost upward on Irving jobs is post work: if the clay has heaved a gate out of square, we’re often adding concrete footer reinforcement and re-welding before the opener itself gets touched. A free estimate includes the diagnostic, the written scope, and the flat price. Call (817) 510-4183 and we’ll put it on paper before any tool comes off the truck.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Ghost Controls Gate Repair in Irving
Summer heat expands the metal on your gate frame and hardware, and if the gate was already close to binding from clay-driven post movement, the added expansion is what pushes it over the edge. The opener’s force sensor then trips mid-travel because it’s working harder than the motor was rated for. The fix is usually post re-shimming and a travel-limit recalibration, not a new opener. Call (817) 510-4183 for an exact quote.
The R20 is rated for residential slide gates up to 1,200 pounds and 40 feet of travel. Many Las Colinas ornamental iron slide gates fall within that rating, but if the gate is heavier than the spec or the track is already worn from clay movement, the R20 will burn through its duty cycle early. We check the gate weight and track condition before recommending the R20, and we’ll tell you plainly if the gate needs our Gate Installation in Irving team to handle track work first.
Usually not. Storms in Irving bring power surges that knock the receiver’s stored remote codes offline. The opener still runs from the hardwired keypad. We reprogram the receiver, test every remote, and if the surge took out the receiver board, we replace it. Most of these calls are under an hour.
We replace the limit switch by itself whenever the motor is still holding its rated torque and the gear reduction isn’t worn. A limit switch is a $40 to $120 part plus labor. A whole motor assembly is $450 to $700. We’ll show you the test readings that justify the smaller fix before we ever suggest the larger one, and the written price covers exactly the work being done.
Yes. We tie Ghost Controls systems into HOA phone-entry and keypad systems across Irving regularly, especially in Las Colinas subdivisions where access control is managed by the association. The Ghost Controls receiver accepts wired and wireless trigger inputs, so we can usually integrate without replacing the opener. Call (817) 510-4183 and we’ll tell you what’s compatible with your existing system.
Service Areas Near Irving
We run Ghost Controls service across Irving and the surrounding Metroplex. In addition to our work here in Irving, our team covers nearby Euless for Ghost Controls service in Euless, plus Coppell for Ghost Controls service in Coppell. You can see the full reach on our Irving service area page, which maps coverage from Grapevine through Bedford and Carrollton.
Book Your Ghost Controls Service in Irving Today
If your Ghost Controls gate is stalling, binding, or dead after the last storm, call (817) 510-4183. A live person answers, we schedule the trip, and the price is written down before any work starts. If the repair isn’t right, our 365-Day Done Right Promise covers it. No argument, no fee.
Written by Adrian Vance, Owner at Vance Gate Repair Irving, serving Irving since 2014.