Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Repair for Irving Homeowners
When a driveway gate stops opening, sags on its hinges, or grinds halfway across its track, you need a technician who will tell you what’s wrong, write down the price, and fix it. Vance Gate Repair has repaired over 22,000 gates since 2014, and every one of those jobs started with a written price before any work began. We answer the phone 24 hours a day with a live person, not a voicemail queue, and our technicians arrive in Irving with the tools, the parts, and a camera. Call (817) 510-4183 for a free estimate on gate repair in Irving, TX.
We service every common failure on residential driveway gates: dead motors, misaligned photo-eyes, snapped limit switches, rusted hinges, bent posts, and welds that finally gave out after years of Texas heat and wind. If you’ve already tried the obvious reset and the gate still won’t move, we’ll find the cause, show you a photo of it, and hand you a written price before we touch a tool. That’s how Adrian Vance has run this company from day one.
Key Takeaways
- Written price in your hand before any repair starts, not after
- Same-day gate repair available in Irving for most mechanical and electrical failures
- We service FAAC, BFT, Linear, Viking, and five other major automation brands
- Every visit ends with a photo log of what was found, adjusted, and replaced
- 365-Day Done Right Promise covers every completed repair, no fine print
What Our Gate Repair Service Includes
Gate repair is not one job; it’s a family of failures that share a common symptom: a gate that won’t open or close the way it should. Sometimes the problem is electrical. Sometimes it’s structural. Sometimes it’s a control board that lost its memory after a power surge. Here is exactly what we fix under the heading of gate repair in Irving, and how we handle each one.
Electric Gate Repair
Electric Gate Repair usually traces to a handful of components: a control board, a limit switch, a capacitor, a photo-eye, or a wiring connection that has corroded or pulled loose. We diagnose the circuit with a multimeter, not by guesswork, and we replace only the part that failed. When we finish, we photograph the board settings and the new component so the next service visit, if there ever is one, starts from a record instead of a mystery.
Automatic Gate Repair
Automatic Gate Repair adds a layer of complexity: the automation system that reads the signal from your remote or keypad and drives the motor. When a gate opens on its own, stops halfway, or refuses to respond to a remote that worked last week, the problem is usually in the receiver, the loop detector, or the motor itself. Vance Gate Repair Irving works on whatever automation is already installed on the property rather than steering you toward a replacement you may not need. Nine major brands, one service call.
Hinge & Post Repair
A sagging gate is almost always a Hinge & Post Repair problem. The hinge barrels wear oval, the post shifts in its concrete footing, and the gate starts dragging on the pavement or pulling against the opener motor. For swing gates, we replace worn hinges, re-set posts in fresh concrete where needed, and re-square the gate leaf before tightening anything down. For slide gates, we inspect the rollers and the guide posts, because the same sag shows up differently on a rolling gate.
Gate Realignment
Even a gate that was installed straight can shift over time: the ground settles, the post leans, the chain stretches, the track bends. A misaligned gate works harder, wears faster, and eventually burns out a motor that was never the real problem. We perform Gate Realignment to manufacturer spec, measure the travel path with a tape and a level, and set the limit switches so the gate stops where it should instead of slamming or stalling. Realignment often extends the life of the whole system by years.
Lock Repair
Some gates have mechanical locks, some have magnetic locks tied to the access control system, and some have both. When a lock fails, the gate may stay closed when you need it open, or it may not secure at all, which defeats the point of a gate on an Irving driveway. We repair Maglocks, solenoid locks, and simple mechanical latch hardware, and we test the lock’s release with the automation system before we leave. A gate that opens but cannot secure is a half-finished repair.
Weld & Rust Repair
Steel and iron gates in North Texas take direct sun, rain, and the occasional ice storm. Rust starts at the welds, at the bottom rail, and anywhere water pools. We grind out the rot, weld in new steel, and reinforce the original joint so the strength comes back. A cracked weld that is left alone will fail completely, usually at the worst moment, and the gate will drop. We fix the weld before the gate falls off its hinges.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Repair
We are authorized to service and stocked to repair a wide range of gate automation equipment. Of the brands we see most often in Irving, FAAC units are common on heavier swing gates. These are hydraulic and electromechanical operators that demand precise limit settings, and we have set enough of them to know that a FAAC motor is rarely the first thing to fail. Usually the problem is a relay on the control board or a limit switch that drifted out of adjustment. We stock the common parts and the uncommon patience to work through the wiring diagram rather than rip out a motor that still has years left.
BFT and Linear equipment appear on many mid-sized residential installations. BFT gear tends to be sensitive to power irregularities, so we always check the incoming voltage and the capacitor before we open the gearbox. Linear actuators are simpler machines, which means their failures are usually mechanical: a limit switch, a belt, or a coupling. Viking units, especially the vehicular swing and slide operators, are built for heavy cycles, and when they fail, the cause is often in the control panel or the ground loop wiring, not the motor itself. Whether you have one of these brands or any other make, we can help, and we won’t steer you toward replacing equipment that can be repaired.
BeforeAfterSigns You Need Gate Repair Right Now
Gates rarely fail without warning. Here are the warning signs we hear about most often, and what each one means for the system.
- The gate hesitates or stops and reverses partway. This is often a limit switch or a safety sensor issue. The motor thinks something is in the way, or it does not know where it is. Left alone, the gate will start slamming or stalling, and the motor will take the abuse.
- The gate is loud, grinding, or shaking. Grinding sounds are metal on metal, usually a bearing or a gear that has lost its lubrication or is already failing. Shaking during travel usually means the tracks, rollers, or hinges are misaligned. Noise is the gate asking for help before something breaks.
- The gate only works with the hardwired keypad, not the remote. If the remote stopped working but the keypad works, the problem is usually the receiver or the remote itself. If neither works, the control board is suspect. Either way, the gate is not going to fix itself on its own.
- The gate is sagging or dragging on the ground. A gate that drags has already worn through its hinge or roller tolerance. Every cycle grinds the problem deeper, and eventually the motor will pull more current than it was designed to draw. That is how a $200 hinge job becomes a $1,200 motor job.
- You can see rust through the paint or cracks at the welds. Rust is not cosmetic. It will spread underneath the paint and eat the steel until the gate fails structurally. On a driveway gate, a structural failure means the gate falls, and that is a safety problem, not just a repair job.
If you are seeing any of these signs on your gate in Irving, call (817) 510-4183. We will come out, diagnose the problem, and give you a written price before any work begins.
Our Gate Repair Process - Step by Step
Every gate repair follows the same sequence, because the sequence is what protects you from surprise invoices and us from guesswork. Here is how it works.
- 1
Diagnosis and documented evidence. We arrive, listen to your description of the problem, then test the system ourselves. We check voltage at the motor, the board, and the transformer. We open the covers and look for corrosion, burned connections, and mechanical wear. We photograph what we find, because the evidence is part of the job record.
- 2
Written scope and written price. Before any tool comes out, we hand you a written description of the repair and a flat price for the work. No ranges, no “depending on what we find.” The price you see is the price you approve. That is Haven Standard Clause 1, and it is the rule we have followed on every job since 2014.
- 3
The repair itself. We replace the failed component, reset the adjustments, and re-align what needs re-aligning. We use the trade’s real vocabulary and show you what we are doing: a limit switch set to the correct degree, a photo-eye aligned to manufacturer spec, a hinge reamed and bushed to remove the slop.
- 4
Testing and verification. We cycle the gate a minimum of ten times after the repair. We test the safety sensors, the remote range, the force settings, and the stop points. If the gate fails any test, we repeat the adjustment until it passes. The gate is not done until it works like a gate, not like a compromise.
- 5
Documented handoff. Before we leave, you get a photo log of the work: what we found, what we replaced, and what we set. The part number goes in the written record. If anyone ever needs to service that gate again, the record is there. That is Haven Standard Clause 4, and it costs you nothing extra.
How Much Does Gate Repair Cost in Irving?
A typical gate repair in Irving runs between $180 and $650, depending on the failure. Here is what that looks like in practice: a misaligned photo-eye or a failed limit switch usually falls between $180 and $250. A worn hinge or a bent post repair ranges from $250 to $400 per hinge or post. A capacitor or a small control board component runs $200 to $350. A motor replacement on a swing gate is the big one: between $550 and $1,200 depending on the brand and whether the arm bracket is intact.
What affects the price: the brand of the automation equipment, the condition of the steel around the failure, and whether the failure is electrical or structural. Electrical repairs are usually faster. Structural repairs, like welding or post re-setting, take longer and cost more because the material and the labor are heavier.
How to avoid overpaying: get the price in writing before the work starts. Every legitimate technician knows what the repair is after diagnosis, and the diagnosis is free when you book the repair. We hand you the written price and you decide. No pressure, no surprise invoice. That is the whole point of the Haven Standard.
Our free estimate includes the service call, the diagnosis, the photo documentation of what we found, and a written price for the repair. You pay for the repair, not for the honesty. Call (817) 510-4183 to schedule.
Gate Repair Near Irving - Our Service Area
Our technicians arrive in Irving from our local dispatch and typically reach most addresses within 60 to 90 minutes for emergency calls. We cover the surrounding communities, including Gate Repair in Euless, Gate Repair in Coppell, Grapevine, Bedford, Carrollton, Colleyville, Southlake, Hurst, Grand Prairie, Dallas, and Arlington. If you are unsure whether we cover your street, call (817) 510-4183 and a live person will tell you.
Serving Irving, TX - Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Repair in Irving
Gate repair is the process of diagnosing and fixing any failure that prevents a driveway gate from opening, closing, securing, or operating safely. It includes electrical work on motors, control boards, limit switches, and photo-eyes, plus mechanical work on hinges, posts, rollers, tracks, welds, and locks. Vance Gate Repair Irving handles the full range, with a written price before any work starts and a documented photo record when the job is done.
Most common gate repairs take between one and two hours once the technician is on site. Simple electrical fixes, like replacing a limit switch or realigning a photo-eye, often run under an hour. Structural repairs like hinge replacement, post re-setting, or welding take longer, sometimes three to four hours, because the material needs time to set or cool. We will tell you the expected time in the written estimate before we begin.
The cost depends on the failure, but most repairs in Irving fall between $180 and $650. Electrical component replacements, like limit switches or capacitors, run $180 to $350. Hinge and post repairs run $250 to $400 per hinge or post. A full motor replacement on a swing gate can reach $550 to $1,200 depending on the brand. Every price is written before the work starts, so you never approve a repair and then meet a different invoice. Call (817) 510-4183 for a free, written estimate.
Yes. We service FAAC, BFT, Linear, Viking, and five other major gate automation brands. We stock common OEM parts for these systems and our technicians work from the manufacturer’s wiring diagrams, not from guesswork. If your gate has a motor we have not named, call us and ask. The answer is probably yes.
In most cases, yes. A live person answers our phone 24 hours a day and can dispatch a technician to Irving the same day, often within 90 minutes. If your gate is stuck open and your property is not secure, call (817) 510-4183 now. We will tell you what we can do and when we can be there, and you will get a written price before the work starts.
Every gate repair we complete is covered by our 365-Day Done Right Promise. If the repair is not right, we make it right within one full year, no argument and no additional fee. The warranty is in writing, and the photo record from your job is what we use to verify the original condition and the work we did. That record protects you and us both.
You do not need to do much. If your gate has a manual release, leave it in whatever position it is in and do not try to force it. Clear the area around the gate and the motor so we have room to work. If the gate uses a keypad or a remote, have those ready so we can test the full system. We handle the rest, including the documentation.
Schedule Your Gate Repair Service in Irving Today
If your gate is broken, sagging, or just making a sound it never made before, call (817) 510-4183 now. A live person will answer, ask what is happening, and schedule your service call. The estimate is free, the diagnosis is documented, and the price is written before any work begins. That is how we have repaired 22,000 gates since 2014, and it is how we will repair yours.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Irving since 2014.