Ghost Controls Gate Repair Service Nationwide

Why Irving Homeowners Choose Ghost Controls Gate Repair

We provide independent Ghost Controls in Irving gate repair service throughout Irving, TX, and the work we do on these openers goes deeper than swapping a board and hoping. Our technicians work on Ghost Controls systems daily, from legacy AXDP dual swing arms to current R-Tank battery and solar kits, so we know their board logic, limit tuning, and mounting quirks without wasting time on guesswork. We are not authorized by or affiliated with Ghost Controls, and we don’t pretend to be. What we are is an Irving gate company that sees these openers on ornamental iron gates across Las Colinas, Valley Ranch, and older North Irving neighborhoods, and we fix them with written pricing before any tool comes off the truck. Call (817) 510-4183 for a free estimate on your Ghost Controls repair.

Call (817) 510-4183

Why Trust Vance Gate Repair Irving for Your Ghost Controls Gate Repair?

Ghost Controls openers have a particular set of failure patterns that a generalist gate technician often misreads. The AXDP and AXPO swing arms use a master/slave logic that confuses techs who mostly see LiftMaster or Mighty Mule. The TSS1 heavy-duty solar swing carries a gearbox that wears differently than lighter residential arms. The R-Tank battery system behaves like a solar-charged DC opener, not an AC unit, and diagnosing it requires understanding how the charge controller interacts with the panel and the battery chemistry, not just checking voltage at the motor.

Adrian Vance started in commercial access-control work back in 2014, and that background shows in how we document every Ghost Controls job. When we trace a master/slave communication fault, we photograph the corroded wire, the replacement, and the new connection point. When we reset limit switches, we record the before and after readings. You get a photo log and a written note explaining what we found, what we replaced, and what to watch for next. That documentation habit came from years of commercial sites where the next technician had to understand exactly what the last one did. Name what you found. Name what it costs. Name what you left behind. That’s the standard on every Ghost Controls repair we do in Irving, and the 365-Day Done Right Promise backs it: if the repair is not right within a full year, we make it right at no additional charge.

Common Ghost Controls Gate Repair Problems We Fix in Irving

• MXA and TSS1 gearbox output shaft wear. The TSS1 is rated for heavier gates, but on the ornamental iron swing gates common in Las Colinas HOA communities, the gearbox output shaft wears over time, causing the arm to slip or chatter mid-travel. We see this on TSS1 units that have been in service five to seven years, especially on gates wider than 14 feet. The fix is a gearbox rebuild or replacement, not always a full arm swap.
• R-Tank batteries losing capacity in Texas heat. Irving summers regularly push past 100°F, and the R-Tank’s 12V battery sits inside a housing that absorbs that heat. A battery that reads fine on a cool morning will stall the opener mid-travel at 4 p.m. when the housing temperature is 120 degrees. We test under load, not just open-circuit voltage, and replace batteries that have lost meaningful capacity. A battery showing 12.6 volts at rest but dropping below 10 volts under load is done, regardless of what a generic tester says.
• AXDP master/slave communication faults. On dual gate AXDP systems, the slave arm occasionally stops responding to the master. The board blinks a fault code, and the gate opens one leaf only. We trace the communication wire between the two arms, and in Irving’s clay-heavy soil, we often find moisture intrusion at the conduit joints or a corroded connector. This is a wiring diagnosis, not a board replacement, and misdiagnosing it as a board failure wastes money.
• Factory limit nuts backing off. Ghost Controls swing arms use mechanical limit nuts to set travel, and on gates that cycle frequently, those nuts can back off over months of vibration. The result is an opener that over-travels and slams the gate into the post or the stop. We reset the limits, mark the new position, and photograph the setting so the next adjustment is documented.
• Remote control range and receiver faults on older Ghost Controls boards. Older Ghost Controls receiver boards sometimes lose range gradually, and homeowners assume the remote battery is the problem. We test the remote output, the receiver sensitivity, and the antenna path before recommending anything. Sometimes it’s the remote. Sometimes the board’s receiver section has degraded and needs replacement.

If your Ghost Controls opener is showing any of these symptoms in Irving, call (817) 510-4183. We’ll tell you what we think over the phone, and if we come out, the written price is in your hand before work starts.

Before

After

Ghost Controls Parts & Our Repair-vs-Replace Approach

We use OEM Ghost Controls boards, arms, and limit switches whenever they are available from our local supplier. For discontinued models, we install quality aftermarket components only when they match the torque curve and mounting geometry of the original. A generic 12V linear actuator will not substitute for a Ghost Controls AXPO arm unless the stroke length, force rating, and duty cycle all line up, and we verify that before suggesting it.

Our position on repair versus replace is simple: we repair what is salvageable. If a TSS1 gearbox has a worn output shaft but the motor and board still test good, we price the gearbox work and let you decide. If an R-Tank battery is dead and the charge controller still regulates properly, we replace the battery, not the entire kit. Pushing a full kit replacement on a gate that needs a $75 limit switch is not how we operate, and the written price you get reflects that. Call (817) 510-4183 for a straight answer on what your Ghost Controls opener actually needs.

Our Ghost Controls Service Process - Step by Step

1. 1
   Diagnosis. We test the board, battery or transformer, limit settings, and arm movement. On a Ghost Controls system, we check the master/slave communication first if both arms aren’t responding, then work through the power path. We document what we find with photos and readings.
2. 2
   Written price. Before any repair work starts, you get a written scope and a flat price. That’s Haven Standard Clause 1, and it applies to every Ghost Controls job we do in Irving. The price is agreed before anyone picks up a tool.
3. 3
   Repair or installation. We install OEM or properly matched aftermarket parts, set limits to the correct travel, and torque every mounting point. For solar systems, we verify the panel angle and charge controller settings, not just the battery voltage.
4. 4
   Testing. We cycle the gate through multiple full open and close runs, test the safety features including photo-eyes and obstruction detection, and confirm remote control operation. On dual gates, we verify the master and slave arms stay synchronized through at least five full cycles.
5. 5
   Documentation and warranty. You get a photo log of every adjustment and a written record of the part numbers installed. Every Ghost Controls repair carries the 365-Day Done Right Promise: one full year for us to make it right at no additional charge.

Ghost Controls Products We Service & Install in Irving

We service and install the full Ghost Controls line we encounter across Irving, including Ghost Controls in Coppell and nearby areas: the AXDP dual gate swing arm, AXPO single swing arm, R-Tank 12V battery and solar opener, and the TSS1 heavy-duty solar swing. We work on older Ghost Controls boards still running in the 1950s and 1960s ranch neighborhoods of North Irving and Irving Heights, and we stock common replacement parts locally, including limit switches, batteries, remotes, and communication wire, so a typical repair doesn’t wait on a week-long parts shipment.

We Also Service These Brands

Ghost Controls is one of nine major gate automation brands our technicians service, along with Gate Repair for all major systems. If your property has a LiftMaster on the driveway gate and a Ghost Controls on the pedestrian gate, one call covers both. We also work on Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, and Elite systems across Irving.

FAQs - Ghost Controls Gate Repair Service in Irving

My Ghost Controls R-Tank opener is not holding a charge even with the solar panel connected. What is wrong? Usually the battery has lost capacity from heat exposure or age, and the solar panel cannot replenish it fast enough during short winter days. We test the battery under load and check the charge controller output to confirm whether you need a battery, a panel, or both. Call (817) 510-4183 for a diagnostic visit.

Why does my Ghost Controls AXDP slave arm stop halfway and blink a fault code? The slave arm is not receiving a clean signal from the master, and in most Irving installs, that traces to a corroded communication wire or a loose connector at the conduit joint. We test the wire path before replacing any board. It’s a wiring diagnosis, and it usually fixes the fault without a board swap.

Can I replace just the gearbox on a Ghost Controls TSS1 opener instead of the whole arm? Yes, in most cases. The TSS1 gearbox output shaft is a known wear point, especially on wider ornamental gates, and if the motor and board still test good, a gearbox rebuild or replacement restores full travel. We price the gearbox work separately so you don’t pay for an entire arm assembly you don’t need.

My Ghost Controls gate opens fine but slams hard when closing. Is that a safety issue? Yes, it is a safety issue, and it’s usually caused by limit nuts that have backed off, allowing the opener to over-travel past the intended stop point. A gate that slams can injure someone or damage the gate frame. We reset the limits, mark the new setting, and photograph it for the record. Call (817) 510-4183 before it gets worse.

Will a generic 12V solar panel work with my Ghost Controls opener, or do I need the OEM panel? A generic panel will work if the voltage and wattage match the charge controller’s input range, but some Ghost Controls charge controllers are finicky about panel voltage at low light. We match panels to the controller’s input specs rather than guessing. Using an oversized panel on a controller rated for a specific voltage range can cook the controller. We verify before installing.

How much does Ghost Controls gate repair cost in Irving? Most Euless Ghost Controls service and Irving repairs run between $180 and $450, depending on whether we’re replacing a limit switch, a battery, a communication wire, or a gearbox. Full arm replacements run higher, typically $600 to $1,100 including parts and labor. You get a written price before any work starts, so the number you agree to is the number you pay. Call (817) 510-4183 for an exact quote, estimates are free.

Book Your Ghost Controls Service in Irving, TX

Call (817) 510-4183 and a live person answers, any hour of any day. We’ll schedule your Ghost Controls diagnostic, send a background-checked, uniformed technician with a name and photo before arrival, and put the written price in your hand before any work begins. Free second opinions on any written estimate from another company. The estimate is free, the record is yours to keep, and the repair is covered for a full year.

Written by Adrian Vance, Owner at Vance Gate Repair Irving, serving Irving since 2014.