Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Hurst
Gate repair in Hurst usually falls into one of two categories: a gate that won’t swing or slide because the hardware has failed, or a gate that still moves but racks, drags, and leans because the post has shifted in the clay. Most Hurst homes were built between the 1960s and 1980s, which means the original gate posts were set without the footing depth that today’s soil conditions demand. We reset posts, replace sheared hinges, and bring legacy automatic operators back to working order. If your gate is binding, sagging, or dead at the motor, call (817) 510-4183 and a live person answers.
Our crews serve Hurst neighborhoods from Bellaire Drive to the Shady Oaks area, and we schedule around your day, not ours. We write the price before we start, and we photograph what we found before we leave.
Why Vance Gate Repair Irving Is Hurst’s Preferred Gate Repair Company
Hurst homeowners tend to do their homework before they call anyone. They have already read the reviews, they know what a swing gate should do, and they want to see a number before a truck shows up. That’s exactly how we work. Every visit starts with a written price, handed over before any tool comes out. That’s Haven Standard Clause 1, and it’s not a pitch, it’s our paperwork habit.
Adrian Vance built this company in 2014 out of commercial access-control work, and that background shows up on residential jobs in Hurst. We don’t do verbal estimates and a handshake. We document what we find, what we adjust, and what we install, then leave that record with you. If a gate acts up again within a year, the 365-Day Done Right Promise means we make it right at no charge.
We also know this market specifically. Hurst is nearly built out. The gate call we get most is not a new install, it’s a 40-year-old post that has crept out of plumb after another dry summer. More on that below, because it drives almost every decision on this page.
Our Gate Repair Services in Hurst
Gate Realignment
Realignment is the most common repair we perform in Hurst, and it’s almost never just a hinge adjustment. When an original 4×4 or steel post set in Blackland Prairie clay starts to move, the gate frame racks, the latch misses the strike, and the operator strains against the extra load. We measure the post lean, check the footing condition, and decide whether the gate can be re-hung or the post needs to be reset. In older Hurst subdivisions around Precinct Line Road and Bellaire Drive, the honest answer is usually the post reset.
Hinge & Post Repair
Hurst’s clay soil swells in wet springs and shrinks in dry summers, and that cycle works on gate posts every single year. The concrete collar cracks, the post leans, and the lag-bolt hinges shear under decades of torque from the shifting frame. We replace worn hinge hardware with heavy-duty components and reset posts deeper into fresh concrete. Patching the collar alone rarely holds through the next August.
Electric Gate Repair
Electric gate operators on older Hurst properties often fail from heat and metal expansion, not from a burned motor. A control board that worked fine in March will bind and fault when the August sun pushes surface temperatures past 140°F. We diagnose the board, the limit switches, and the sensor alignment before recommending anything. Where a retrofit makes sense, we do it. Where the board is obsolete and parts are gone, we say so plainly and give you the replacement cost in writing.
Automatic Gate Repair
Automatic gate repair in Hurst usually involves a legacy operator that has outlived its original safety sensors. UV-degraded photo-eyes, cracked wiring insulation, and limit switches that drift in extreme heat are all common. We service Gate Repair jobs on LiftMaster, FAAC, Mighty Mule, and Elite operators, among others, and we recalibrate the travel and force settings for the gate as it actually sits today, not how it sat when it was installed.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Hurst
We work on nine major gate-automation brands, and that matters in a city like Hurst where the operator on the gate may be 15 or 20 years old. If your property has a FAAC swing arm or a Mighty Mule that stopped responding, we can usually diagnose and repair it without swapping the whole system. We keep common boards, sensors, and hardware in local stock so Hurst customers don’t wait a week on a parts order. LiftMaster, Elite, and FAAC repairs are all routine for our crews.
Common Gate Repair Problems We See in Hurst Homes
- Post heave and lean on aging footings. The 4×4 or steel posts on Hurst’s original gates were set shallow in clay-heavy soil. Every wet spring and dry summer shifts them a little more, and eventually the gate drags or won’t latch.
- Sheared lag-bolt hinges on original wood gates. Decades of frame torque from clay movement twists the hinges until the bolts snap or strip out. Replacing a hinge without addressing the post lean is a temporary fix.
- Obsolete control boards on legacy operators. Boards that have baked through 20 Hurst summers fail in ways that look like motor failure. We bench-test before we condemn anything.
- UV-degraded safety sensors. Photo-eyes and edge sensors on 1990s and 2000s gates crack and yellow in the Texas sun, causing phantom reversals or fault codes that shut the gate down entirely.
Pricing for Gate Repair in Hurst, TX
We post pricing ranges because a written price is the whole point. For gate repair in Hurst, here’s what we typically see:
- Gate realignment and hinge adjustment: $145-$295
- Hinge replacement with heavy-duty hardware: $180-$420, depending on gate weight and access
- Post reset with fresh concrete footing: $350-$800, depending on post material and depth
- Electric gate diagnosis and control board replacement: $225-$650
- Automatic gate operator full replacement: $850-$2,400, varies by brand and arm type
Every price is quoted in writing before work begins. No upsell at the door, no surprise line item at the end. If another company has given you a written estimate, bring it, and we’ll review it free under our second-opinion offer. Call (817) 510-4183 to schedule.
We Also Serve Cities Near Hurst
Our Hurst crews also cover Bedford, Colleyville, Euless, and Southlake. If you’re just outside the Hurst city line and your gate is acting up, give us a call. We’ll tell you straight if we can get to you quickly.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Hurst
Because the post was set in Blackland Prairie clay without a deep enough footing, and that clay shrinks several inches during the late-summer drought, pulling the post out of plumb again. A hinge adjustment fixes the symptom and lasts until the next dry cycle. A post reset with a deeper concrete footing is the only fix that lasts through multiple seasons. Call (817) 510-4183 for an exact quote on your specific gate.
No. Once the concrete collar around the post has cracked, the post is no longer locked into the footing, and patching the collar is cosmetic. The crack means the clay below has already moved enough to fracture concrete, and that movement will continue. The post needs to be removed, the footing dug deeper, and the post reset with new concrete and new hardware. We do this regularly in Hurst and can give you a written price before any work starts.
It depends on the gate’s structural condition, not its age. If the post is sound and the frame is square, a modern operator can be fitted. If the post has moved and the frame is racked, the gate will bind against any opener you put on it. We’ll tell you which situation you have and write the price for either retrofit or replacement. You won’t pay twice to rediscover the same problem.
Entrapment protection on older gates means photo-eyes, edge sensors, and force settings designed to stop and reverse the gate if something blocks it. After years of Hurst sun and the gate frame shifting, those sensors can be misaligned, cracked, or falsely calibrated, and the gate may not reverse when it should. We test the full safety circuit on every automatic gate repair visit and photograph the readings. If a sensor is degraded, we replace it before it becomes a failure. Call (817) 510-4183 to schedule a safety check.
Post heave from Blackland Prairie clay movement. The post shifts, the frame racks, the hinges shear, and the operator burns out trying to move a gate that no longer swings true. In neighborhoods around Bellaire Drive and along Precinct Line Road, we see this failure mode more than any other. The fix is a proper post reset with updated hardware, not another hinge replacement. Estimates are free and written.
Contact Vance Gate Repair Irving for Gate Repair in Hurst
If your gate is sagging, binding, or dead at the operator, call (817) 510-4183. A live person answers, day or night. We’ll schedule a Hurst visit, write the price before any work starts, and leave you a documented photo record of what we found, what we fixed, and what it cost. That’s how we work, and it’s in writing before the first tool comes off the truck.
Written by Adrian Vance, Owner at Vance Gate Repair Irving, serving Hurst since 2014.
Gate Repair in Nearby Areas
