Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLinear Hinge & Roller Replacement: The Irving Owner’s Guide
We stock and install Linear-compatible hinge and roller replacement parts in Irving, with most jobs running $185-$380 installed depending on your gate’s size, weight, and whether both hinges or a complete roller set need replacing. Most Irving homeowners discover the problem as a gate that drags, scrapes the concrete, or sags badly on one corner while the motor still runs fine. The operator is working; the hardware under it is not. We carry the common Linear part numbers on the truck for same-day repair in most cases.
Before you keep reading: if your gate has come off a rail or is hanging dangerously, shut the operator off at the breaker and call us. A sagging gate is heavy, and a bad roller can let it drop without warning.
Which Linear Models This Applies To
Linear makes slide-gate hardware and operators under several model families: the LRA and SLR slide operators, the APeX and PRO series for heavier commercial gates, and residential slide kits sold through dealers. The hinge and roller terminology matters here. Slide gates ride on fixed rollers bolted to a steel channel; swing gates pivot on bearings or welded hinges. When an Irving owner calls about a “Linear hinge and roller replacement,” what they usually mean is one of two things: the carrier rollers under a sliding gate have worn flat, or the hinge bearings on a swing gate that a Linear operator drives have begun to seize.
The compatibility gotcha: Linear does not make its own hinges or rollers for swing gates. Those are structural hardware, sold by the gate fabricator, in sizes that vary by gate weight and thickness. Linear makes slide operators and some slide hardware kits, but the load-bearing components under a Linear-driven swing gate are generic to the gate, not the motor. That matters because the right replacement part depends on the hinge’s bearing size and bolt pattern, not on which operator sits on top. We measure the old part on site before quoting anything, so an owner doesn’t order the wrong bearing online and pay twice.
For slide gates, the rollers under a Linear-driven panel are often replaceable as individual truck assemblies with a steel wheel, sealed bearing, and adjustment bolt. These are serviceable parts. We carry several wheel diameters in the truck because Irving’s clay soil and drainage patterns mean rollers wear unevenly on the low side of the track.
Signs Your Linear Hinge & Roller Replacement Is Failing
- The gate scrapes the driveway or concrete pad. A roller wheel has gone flat or the hinge bearing has worn enough for the panel to drop. The scrape gets worse fast once steel touches concrete.
- The gate sags toward the free end when open. This is usually a hinge bearing worn oval. The operator still moves the gate, but the dead weight is pulling at the bolts and the gate frame twisting.
- The motor sounds labored or stalls mid-cycle. A Linear operator will push through a dragging hinge for a while, but the amp draw climbs, the thermal overload trips, and eventually the board or transformer fails. Replacing a hinge now is cheaper than a motor later.
- The gate rattles or hops as it travels. A roller with a flat spot or a bearing with play causes chatter in the panel. It sounds like a metallic knock once per wheel revolution.
- You can lift the gate and feel slop at the hinge point. That vertical play is measurable. A bearing with more than about an eighth of an inch of travel is done.
BeforeAfterReplacement Cost & What’s Included
In Irving, expect to pay between $185 and $380 for a typical Linear hinge and roller replacement, installed. That range covers removing the old hardware, drilling or re-threading bolt holes where the frame is worn, setting the new components, and adjusting the gate so it travels level and closes square. If your gate is oversized, powder-coated, or the hinge posts are pulled out of plumb, the price can go higher, but we write that number down before any work begins.
The price we quote is the price on the invoice. We do not start a job until you’ve seen the written figure. Under Clause 1 of our Haven Standard, every job gets a written scope and written price handed over before tools come out. The replacement parts themselves carry a manufacturer warranty against defect, and our work is covered by the 365-Day Done Right Promise: if the repair isn’t right within a year, we make it right at no charge.
One honest note: aftermarket rollers and hinge bearings vary wildly in quality. A $12 import roller with an unsealed bearing will fail again in a Texas summer. We install sealed-bearing hardware built for the dust and heat of an Irving summer, and we document the exact part number on your invoice so a future tech isn’t guessing.
DIY or Call Us?
Some things on a gate are safe for a careful homeowner. You can check the obvious: look for a wheel that’s no longer round, check the hinge bolts for looseness, and see if the gate has dropped on one side. That’s worth doing. But actually swapping a loaded hinge or roller on an operating gate is a different job. The gate panel weighs hundreds of pounds, and if the old hinge is under tension or the panel shifts during removal, it can crush a hand or pin a leg.
On slide gates, the safety concern is the gate falling off its truck when old rollers are pulled. On swing gates, it’s the panel swinging free when the last hinge bolt comes out. We use support stands and set screws at every step. If you’d rather watch than wrestle it, call (817) 510-4183 for a written quote. That’s the smarter play on this one.
FAQs
Most Irving gates get 5 to 8 years from factory hinge bearings and rollers before the first replacement, but Texas heat and dust shorten that to 3 to 4 years on unsealed aftermarket parts. A sealed-bearing roller on a properly adjusted gate can last a decade or more.
No. A hinge bearing that has worn oval cannot be machined or shimmed back into round. Once the inner race has slop, the only honest fix is replacing the complete hinge or pressing in a new bearing cartridge. We’ll show you the wear before we swap it. Call (817) 510-4183 and we’ll quote the replacement.
Most single-gate hinge or roller replacements run 45 minutes to 2 hours once the panel is supported and the old hardware is removed. If the hinge post needs re-drilling or the gate frame is twisted, it takes longer. We’ll tell you the expected window before we start.
We stock common slide-gate roller diameters and swing-gate bearing sizes, along with hardware for several Linear operator models. If your part is an unusual size, we can usually have it by the next business day. We’ll tell you before we leave the first visit.
Call for a Free Written Estimate
If your Linear-driven gate is dragging, sagging, or rattling, call (817) 510-4183. A live person answers, 24/7. We’ll schedule a visit, get eyes on the gate, and hand you a written price before any work starts. We’ve been doing it that way since Adrian Vance started running service calls out here in 2014. Name what you found. Name what it costs. Name what you left behind.
Written by Adrian Vance, Owner, Vance Gate Repair Irving at Vance Gate Repair Irving, serving Irving and nearby areas.