Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in Irving: What to Know First

Linear gate motor and opener service in Irving typically runs between $185 and $480 for most repairs, with full motor replacements landing between $750 and $1,650 depending on the model and whether the arm bracket survived. We’re an independent Linear service provider, not a factory shop, which means we diagnose what’s actually failing before recommending a single part. Most Irving service calls get same-day or next-day dispatch, and you’ll have a written price before we touch the gate.

Call (817) 510-4183

This page is for Linear owners in Irving who want to know what’s wrong, what it costs, and whether it’s worth fixing. If your Linear operator is dead, grinding, or stopping mid-travel, call (817) 510-4183 and a live person answers.

How Linear Products Fail - and How We Fix Them

• Linear LRA series swing arms: capacitor failure after 3 to 5 Texas summers. The start capacitor sits inside the operator housing where Irving heat builds to 140°F or more. When it swells or splits, the motor hums but won’t move the gate. We test the capacitor under load, replace it with an OEM-spec unit, and photograph the reading before and after.
• Linear slide operators (SLR/SLD lines): limit switch drift causing the gate to stop short or slam. On slide gates, the limit cams ride on a threaded shaft that loosens with daily cycles. We find gates stopping eight inches before the closed position or hammering the end stop. The fix is re-setting the limits with a measurable gap and tightening the cam locks, not just nudging the switch.
• Linear APeX circuit boards: power surge damage to the control board. Irving gets real lightning, and a nearby strike can take out the board’s transformer input even when the motor itself is fine. A visual inspection often shows a blackened trace near the terminal block. We replace the board and add surge suppression on the low-voltage side, which the original install frequently lacks.
• Linear MDR/MDC keypad and receiver integration: phantom open commands or complete signal loss. The MDR series receivers drift off frequency over time, or homeowners change remotes and the receiver never gets reprogrammed. We bench-test the receiver with a known transmitter, confirm whether the board or the remote is the failure point, and replace only what failed.
• Linear battery backup units: the gate works fine on AC but fails when the power drops. Most Irving homeowners only discover a dead battery during an outage. We load-test the backup battery, replace it if it’s below 70% capacity, and wire the charger correctly so the new battery actually charges. A surprising number of original installs have the charger leads reversed.

Our Linear Gate Motor & Opener Process

1. 1
   Call and describe the symptom. You get a live person, not a phone tree. We ask what the gate does, or doesn’t do, and schedule the visit.
2. 2
   On-site diagnosis. The technician tests the operator with a meter, checks the limit settings, inspects the arm or chain, and photographs everything found. We name the part and the problem before we quote it.
3. 3
   Written price, before any work. You get a flat number on paper. Haven Standard Clause 1: the price is written and handed over before a tool comes out. If you decline, that’s the end of it.
4. 4
   Parts decision. We use OEM Linear parts when the unit is under warranty or when aftermarket would change the operator’s behavior. For older out-of-warranty units, we offer quality aftermarket components where they match spec and save real money. The part number goes on your invoice.
5. 5
   Repair, test, and document. We fix the failure, cycle the gate through a full open-close loop, and photograph the final settings. You get that record before we leave.
6. 6
   Cleanup and the 365-Day Done Right Promise. The work area is left clean. If the repair isn’t right within a year, we come back and make it right at no charge. No argument.

Before

After

What Linear Gate Motor & Opener Costs in Irving

Most Linear gate motor repairs in Irving fall in the $185 to $480 range. A capacitor replacement runs $185 to $260. A limit switch reset or replacement is $195 to $310. A control board replacement on APeX or LRA lines typically runs $340 to $520 including the board. Full operator replacements, where the motor, board, and housing are swapped, land between $750 and $1,650 depending on the series and whether we’re reusing the existing mount.

What moves the price: whether the arm bracket or chain is still intact, how old the unit is, and whether we need to fabricate a mounting plate. The price is written and agreed before any work starts. Call (817) 510-4183 and we’ll come out and name the number.

Why Irving Homeowners Call Vance Gate Repair Irving for Linear Work

We’ve repaired and installed over 22,000 gates since 2014, and every single one got a written price before the work started and a documented record when the technician left. That’s the Haven Standard. Adrian Vance started in commercial access control, where you can’t guess at a wiring fault, and that habit carried over: we photograph what we find, write down what we set, and leave you the evidence.

We service Linear daily, but we also work on LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and five other automation brands. That matters because you never get steered toward a replacement you don’t need just because the company only knows one brand. If your Linear operator has life left in it, we’ll tell you. The 365-Day Done Right Promise covers every repair we complete.

FAQs