Linear Gate Installation Nationwide

Linear Gate Installation in Irving: What to Know First

Linear gate installation in Irving typically runs $850 to $2,400 for a complete setup, with most single swing-gate jobs landing between $1,100 and $1,700 including the operator, mounting hardware, and wiring. We complete most installations within two to four business days once parts are in hand. Every job starts with a written price before any tool comes off the truck, and you’ll have that number in front of you before you decide anything.

Call (817) 510-4183

This page is for Irving homeowners who already own a Linear operator or have one specified on a quote, and want installation done by someone who treats the brand as a repair target, not a sales opportunity. Call (817) 510-4183 and a live person answers, any hour.

How Linear Products Fail - and How We Fix Them

Linear’s residential line shows up all over Irving, from older driveways near the Las Colinas corridor to the gated communities off MacArthur Boulevard. These operators are reliable enough in dry conditions to stay in service for a decade, but they fail in patterns we can usually spot before the first screw comes out.

• LDO50 and LDCO800 swing-arm operators: the arm bracket loosens at the gate post. This series mounts the operator arm to the gate with a bracket that takes repeated torque. After a few thousand cycles in Irving’s clay-heavy soil, the post shifts slightly or the bracket bolts back out. The gate gets jerky, then stops mid-swing. Our fix is a bracket re-seat with new hardware and a measured reset of the travel limits, photographed before we put the cover back on.
• Persistent “entrapment” fault that is a photo-eye alignment problem, not a motor problem. We regularly find Linear operators that throw an entrapment error because the photo-eye (the infrared beam that stops the gate if something crosses its path) has been nudged out of alignment by irrigation overspray or wind. Owners assume the motor is dying. It is not. We realign the beam, verify it clears the LED indicator, and test the reversal force. This fix is under $200 on most service calls.
• Factory control board failures on Linear’s older residential boards, especially after power flickers. Northern Irving sees its share of thunderstorms in spring, and Linear boards built before 2012 are vulnerable to capacitor burn after repeated brownouts. We have seen this enough that we check the board’s date-code sticker when we quote a repair. If the board is original and the operator is otherwise sound, we usually install a quality aftermarket board that meets or exceeds OEM specs, which is often less expensive and arrives faster than a backordered Linear part.
• Limit switches that drift after installation by someone who rushed the travel set. On a Linear operator, the limit switch tells the motor exactly where the gate ends its travel. If the installer set the switch at the wrong point, the gate slams into the open or closed jamb every time. We find this on a surprising number of gates that were installed only two or three years ago. We reset the limits to factory travel, cycle the gate ten times, and photograph the switch position so you have a record of where it is set.
• Remote receiver interference in neighborhoods where multiple homes have Linear operators installed. Older Linear openers used fixed-code remotes, which means a neighbor with the same-era system can occasionally trip your gate when they press their remote. We swap in a rolling-code receiver board (Linear’s own or a compatible aftermarket unit), reprogram the remotes, and test from 40 feet away. It is a straightforward fix that resolves a complaint most other companies diagnose as a “bad board.”

Our Linear Gate Installation Process

Here is what a Linear installation looks like when we do it, from your first call to the moment we hand you the photo log.

1. 1
   Call and walkthrough. You tell us what you have: a Linear model number, a gate that is already there, or a bare opening. We ask about power access, gate weight, and how far the gate sits from the house. You get a written estimate, not a verbal “we’ll figure it out.”
2. 2
   Site check and measurement. Our technician checks the post for true, the gate’s weight and swing arc, and the power source. If the post is out of plumb by more than a few degrees, we tell you before installation day and write the fix into the scope.
3. 3
   Parts decision. We discuss OEM Linear versus quality aftermarket parts openly. If your operator takes a part that is still under warranty, we use the OEM part and preserve the warranty. If the OEM part is backordered or priced three times the aftermarket equivalent, we tell you and let you decide. The choice is yours, and the price difference is written down.
4. 4
   Installation. We mount the operator, set travel limits, wire the photo-eyes and any keypad or loop detector you have specified, and run the gate through a full cycle test. We photograph the mounting, the wiring connections, and the limit-switch settings.
5. 5
   Paperwork and walkthrough. You get a written record of every part number installed, where it went, and what it cost. We walk you through remote programming and show you the reversal test so you know the gate stops if something is in the way. The 365-Day Done Right Promise covers the whole job.
6. 6
   Follow-up record. Every photo and note from the visit is filed in your job record. If you ever call back about the gate, we can pull up what was installed and when without you needing to dig for a receipt.

Before

After

What Linear Gate Installation Costs in Irving

Here is what we actually charge, in writing, before any work starts. The numbers below reflect typical Irving single-family residential jobs.

• New Linear operator installation on an existing gate: $850-$1,400 depending on operator model and whether wiring and a photo-eye system are already present.
• Complete single swing-gate installation with Linear operator, hinges, and posts set in concrete: $1,400-$2,200.
• Double swing-gate installation with two Linear operators and synchronizing module: $2,200-$3,800.
• Pedestrian gate with Linear keypad and magnetic lock: $900-$1,700.

What moves the price: gate width and weight, whether power needs to be trenched from the house, post condition, and whether you want a keypad, loop detector, or battery backup. Every quote is a flat, written number, and it is the number you pay. Call (817) 510-4183 for a free estimate on your specific setup.

Why Irving Homeowners Call Vance Gate Repair Irving for Linear Work

We service nine gate-automation brands, and Linear is one of them, but we are not a Linear dealer pushing a demo product. We are an independent Linear service provider. That means when we arrive at your home, the only thing we are trying to do is make the gate work correctly, for as long as possible, at a price you saw in writing before we touched anything. Adrian Vance started this company in 2014 after years on commercial access-control sites, and he built the documentation habit into every residential job: a wiring diagram, a photo log, a written note of what was found and what was set. Name what you found. Name what it costs. Name what you left behind.

If your Linear operator turns out to be beyond reasonable repair, we are the company that can also work on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so the recommendation is never limited by what is in our catalog. And if you have a written estimate from another Irving gate company, we will review it free and tell you honestly whether the work and the price line up. A live person answers the phone 24/7. No voicemail queue.

FAQs