Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGhost Controls Gate Parts & Welding in Irving: What to Know First
We provide independent Ghost Controls gate parts and welding in Irving, typically completing hinge replacements, rail repairs, and custom welding within one to three business days once we diagnose the failure. Most Ghost Controls gate repairs run between $185 and $640 depending on whether we’re replacing a roller, re-welding a post base, or rebuilding a hinge assembly. You get a written price before any work starts, and under Clause 1 of our Haven Standard, that number doesn’t move unless you approve a change in scope.
This page is for Irving homeowners who own a Ghost Controls opener, either a swing-arm model like the REX or a slide-gate model like the SL, and need the physical gate itself repaired, welded, or rebuilt. If your gate won’t move, sags, scrapes the drive, or the post is loose in the ground, that’s what we address here. Call (817) 510-4183 and a live person answers, any hour.
How Ghost Controls Products Fail, and How We Fix Them
Ghost Controls builds dependable openers, but the gate hardware they’re bolted to takes the real beating in Irving. Here’s what we see on service calls, and what we do about it.
- Hinge pin wear on heavy iron driveway gates. We commonly see Ghost Controls REX swing-arm openers bolted to ornamental iron gates that weigh far more than the opener was sized for. The factory hinges take the load, and the pin ovalizes over two or three Texas summers. The gate drops, the opener strains, and the limit switches lose their reference. We cut out the old hinge, weld in a heavier barrel hinge with a greaseable pin, and re-square the gate so the REX arm isn’t fighting gravity.
- Post base rust-through at the weld seam. Irving’s clay soil holds moisture against steel posts during the wet months, and most gate posts rot from the bottom up at the concrete interface. The post looks fine until it doesn’t, then the whole gate leans and the Ghost Controls opener binds mid-travel. We remove the old post, weld a new steel post to a plate base with drainage holes, and re-hang the gate to the opener’s specified travel arc.
- Slide-gate rail sag on Ghost Controls SL-series installs. The SL is a solid slide-gate motor, but a steel V-track rail that wasn’t supported every four feet will bow under a 600-pound gate. The opener’s drive gear then chews through the rack teeth. We re-level the rail on new support stands, weld the rack sections true, and reset the opener’s travel limits. The photo log we leave shows the before and after.
- Stripped receiver threads on the opener-to-gate arm bracket. Ghost Controls arms ship with a cast bracket that clamps to the gate frame. On gates that get yanked by kids or wind, the clamp bolts strip out of the receiver, and the arm flops or detaches entirely. We weld a steel backing plate to the gate frame, re-tap the mounting holes, and reinstall the arm at the correct throw angle. It’s a $90 to $160 fix that keeps the arm from tearing off again.
- Gate roller failures on SL slide-gate systems. The sealed rollers under most Irving slide gates are not sealed. Road grit and clay dust get into the bearings, the rollers seize, and the gate starts dragging. The Ghost Controls opener works harder, pulls more amps, and overheats. We replace the rollers with heavier sealed-bearing units, weld shim plates where the track has worn unevenly, and photograph the amp draw before and after so you see the load drop.
Our Ghost Controls Gate Parts & Welding Process
- 1
You call (817) 510-4183. A live person answers, collects the symptom, and schedules a visit. No voicemail loop, no callback queue.
- 2
We diagnose on-site. Adrian or one of our technicians inspects the gate, the Ghost Controls opener, the hinges, the post bases, and any weld points that show stress cracks or rust bloom.
- 3
You get a written price. Before we touch a tool, you have the flat rate on paper. If we find hidden damage mid-repair, we stop, show you the evidence, and get your approval on the change before proceeding.
- 4
We do the parts decision with you. For hinges, rollers, and latch hardware, we’ll recommend OEM Ghost Controls parts where they’re materially better, and name the quality aftermarket part when it outperforms OEM at a lower price. You decide with the numbers in front of you.
- 5
We weld, repair, and re-set the opener. All welding is done with the opener disengaged so no surge can reach the Ghost Controls board. We re-set travel limits to the new gate geometry after any structural work.
- 6
We document and guarantee. You get a photo log of every weld, every part number, and every limit reading. The entire job carries our 365-Day Done Right Promise.
BeforeAfterWhat Ghost Controls Gate Parts & Welding Costs in Irving
Here are the prices we quote most often on Ghost Controls gates in Irving:
- Hinge replacement (single gate, weld-in): $185 to $340, depending on gate weight and whether we need to re-square the frame.
- Post replacement (steel, set in concrete): $280 to $560 including the new post, concrete, and re-hanging the gate.
- Slide-gate rail repair with support stands: $240 to $520 depending on rail length and how many supports need welding.
- Roller replacement (both rollers): $160 to $290 including sealed-bearing units and track shimming.
- Custom welding (crack repair, bracket fabrication): $120 to $380 depending on access, prep work, and material thickness.
The price moves based on gate weight, how badly the steel has deteriorated, and whether we’re working around an opener that’s still under partial travel. You’ll know the exact number before we start. Estimates are free, and we’ll review any written quote from another Irving gate company at no charge.
Why Irving Homeowners Call Vance Gate Repair Irving for Ghost Controls Work
We’ve repaired and installed over 22,000 gates since 2014, and every one left with a written price agreed before work began and a documented record when the technician pulled away. That’s not a marketing line. It’s how Adrian Vance has run this company since he left commercial access-control work, and it’s what the Haven Standard puts in writing: Clause 1 is the written price, Clause 4 is the photo record on every job. If the repair isn’t right, we come back within the year and make it right at no charge.
We service nine gate-automation brands, so if your Ghost Controls opener is fine but the gate itself needs work, we won’t try to sell you a new motor. We’ll repair the steel and re-set the limits so the opener you already trust keeps working. That same multi-brand bench means if you later add a second gate with a LiftMaster, Mighty Mule, or DoorKing on it, one company handles all of it.
FAQs
We use both, and we tell you the trade-off before you choose. For electronic boards and control components, we use OEM Ghost Controls parts to keep your warranty intact. For structural hardware like hinges, rollers, and brackets, we often recommend a heavier aftermarket part than what Ghost Controls ships from the factory, because the failure is usually in the steel, not the motor. You get the part number and price in writing before we install anything.
Welding on the gate frame, post, or rail does not void the opener warranty, as long as the opener is disengaged from power during the work. We disconnect the Ghost Controls unit before any arc welding so no current can travel back through the control board. The electronics warranty survives. If you have an active warranty claim pending, we’ll document the pre-weld condition with photos so there’s no ambiguity about what we touched.
For hinge and roller failures, yes, if we have the parts on the truck, and we stock the most common Irving patterns. For post replacements and custom welding, we schedule within two to three business days so the concrete can set and the welds can be done properly without rushing. Call (817) 510-4183 and we’ll tell you where your repair falls.
Look at the failure honestly. If a hinge is worn but the post is solid, we replace the hinge. If the post is cracked at the base or the gate frame is splitting at a weld seam, that’s a welding repair. In Irving’s clay soil, a leaning post almost always needs welding or full replacement, and a gate that drags on one side usually has a roller issue at one end and a hinge issue at the other. We’ll name what we found, name what it costs, and name what we left behind. That’s the whole job.
Yes. Every weld we make is covered by our 365-Day Done Right Promise. If a weld cracks, a hinge sags, or a post shifts within a year of the repair, we return and fix it at no additional charge. Name what you found. Name what it costs. Name what you left behind.
If your Ghost Controls gate is sagging, dragging, or pulling its opener out of alignment, call (817) $510-4183. We’ll diagnose it in person, hand you a written price before any work starts, and leave you with a photo record of everything we touched. That’s how we’ve worked since 2014, and it’s how we’ll work on your gate.
Written by Adrian Vance, Owner, Vance Gate Repair Irving at Vance Gate Repair Irving, serving Irving and nearby areas.