Ghost Controls Gate Motor & Opener Nationwide

Ghost Controls Gate Motor & Opener in Irving: What to Know First

We service Ghost Controls gate motors and openers across Irving, and most repairs are completed the same day we diagnose them. A typical Ghost Controls swing-arm motor replacement in Irving runs between $450 and $900 installed, depending on the model and whether the mounting bracket survived the failure. You’ll get a written price before any work starts, not after. If your Ghost Controls gate stopped responding, is beeping but not moving, or reversed mid-travel and locked itself out, this page covers what you’re likely dealing with. Call (817) 510-4183 and a live person answers, any hour.

Call (817) 510-4183

How Ghost Controls Products Fail - and How We Fix Them

• AXDP and HYPRO series: control board failure after power flickers. We see this regularly in Irving neighborhoods where summer thunderstorms knock out power for a few seconds at a time. The Ghost Controls board powers back on but the limit settings wipe, and the gate travels too far or refuses to move. The fix is a board reset and re-learn, or a board replacement when the capacitors are visibly swollen. We photograph the board before and after, so you can see what failed.
• TSS1 and TDS2 swing-arm models: stripped gear inside the actuator arm. When a gate gets pushed by wind (and Irving gets real wind in March and April), the arm fights the manual force and the internal nylon gear strips. The motor still hums but the gate doesn’t move. We replace the gear assembly with the OEM part when available, or a machined aftermarket gear when Ghost Controls is backordered. Either way, you’ll know which one went in and what it cost before we turn a screw.
• GIR3000 and GIR5000 intercom integration: the wired trigger stops firing. Ghost Controls boards accept a dry-contact trigger from a gate intercom or keypad, and that relay on the board is a known weak point after three to five years. When a homeowner presses the intercom button and nothing happens, it’s often the relay, not the intercom. We test the trigger circuit with a meter, replace the relay or the board depending on what the readings show, and leave you the readings in writing.
• Battery backup systems: the gate works on AC but dies on battery. Ghost Controls sells a battery backup kit, and in Irving the batteries degrade faster than the manual suggests because the heat shortens their cycle life. We load-test the batteries under actual motor draw, not just voltage. If the battery can’t hold the gate through a full open-close cycle, we replace it and tag the new one with a date so you know when it went in.
• Photo-eye misalignment on slide gate installations. Ghost Controls slide motors ship with a retro-reflective photo-eye, and the reflector mounted on the opposing post creeps out of alignment as the ground settles. The gate reverses or refuses to close, and the homeowner assumes the motor is dead. We find the beam with a test card, reset the reflector at the correct height, and record the final alignment in the photo log.

Our Ghost Controls Gate Motor & Opener Process

1. 1
   You call (817) 510-4183. A person answers and asks what the gate is doing, not doing, or sounding like. We schedule a visit. You get a text with the technician’s name and photo before we arrive.
2. 2
   We diagnose at the gate. The technician tests the board voltage, checks the limit settings, and listens to the motor under load. On a Ghost Controls job, we check the actuator arm, the control board, the photo-eye, and the battery if one is present. Nothing gets taken apart without your okay.
3. 3
   We hand you a written price. You’ll see the part cost, the labor, and the total, in writing, before any work begins. If it’s a $40 limit-switch adjustment, that’s the price. If it’s a full actuator replacement, that’s the price too. No surprises at the end.
4. 4
   We do the work and document it. Photos of the failed part, the new part, the wiring terminations, and the final travel limits. On Ghost Controls repairs, we note the model and serial number in the job record so future service calls start with a complete history.
5. 5
   We test the gate through full cycles. Open, close, stop, reverse on obstruction, auto-close if equipped. The gate gets cycled until it behaves like the manufacturer intended.
6. 6
   We leave you the record. A written description of what was found, what was replaced, and what to watch for next. Under the Haven Standard, that documentation is standard on every job.

Before

After

What Ghost Controls Gate Motor & Opener Costs in Irving

Here are the ranges we quote most often for Ghost Controls work in Irving. These are installed prices including the part, labor, and our written record.

What moves the price: whether the actuator arm is the OEM part or an aftermarket equivalent, how much of the bracket hardware survived the failure, and whether the control board needs programming after replacement. Every quote is written and handed over before work starts. Estimates are free. Call (817) 510-4183.

Why Irving Homeowners Call Vance Gate Repair Irving for Ghost Controls Work

We’re an independent Ghost Controls service provider, not a manufacturer warranty center, and that independence matters. We repair Ghost Controls motors rather than steering you toward a replacement you don’t need. If a Ghost Controls board is fixable, we fix it. If a gear is stripped, we replace the gear. We don’t sell motors by default.

Adrian Vance has been running service calls across Irving since well before Vance Gate Repair opened its doors in 2014, including regular work around the Las Colinas corridor where Ghost Controls operators sit on both residential driveways and small commercial entrances. His technicians diagnose Ghost Controls failures accurately on the first visit more often than any company you’ll find by searching “gate repair near me.” That’s not marketing language. That’s what happens when someone writes down what they found, sets the limits correctly, and photographs the result every single time.

Every Ghost Controls job gets the 365-Day Done Right Promise: if the repair isn’t right within a year, we make it right at no charge. And if your property has a LiftMaster, Mighty Mule, or DoorKing operator on a different gate, we work on those too. One company, whatever motor is already in place.

FAQs