FAAC Gate Access Control Nationwide

FAAC Gate Access Control in Irving: What to Know First

FAAC gate access control repair in Irving typically runs between $185 and $620 depending on whether we’re replacing a keypad, re-running a damaged wire run, or rebuilding a control board connection. Most FAAC access-control calls we handle in Irving are completed in a single visit because we carry the common FAAC boards, receivers, and keypads on the truck. You’ll get a written price before we touch anything, and if the fix isn’t right, the 365-Day Done Right Promise covers it at no additional charge.

Call (817) 510-4183

This page is for Irving homeowners who already own a FAAC gate system and need the access control working again: keypad entry, remote control, phone entry, card readers, video intercom, or smart access. If your FAAC keypad stopped responding or the gate only opens from the house but not the street, call us at (817) 510-4183. We’re an independent FAAC service provider, not a manufacturer-authorized shop, which means we fix what’s broken instead of steering you toward a full system replacement.

How FAAC Products Fail - and How We Fix Them

FAAC builds solid operators, but their access-control peripherals and low-voltage wiring fail in predictable ways. Here’s what we actually find on Irving service calls:

• E024U control boards losing keypad programming after power interruptions. The E024U is common on FAAC swing gates in Irving, and it’s sensitive to the power flickers we get during spring storm season. The board drops stored transmitter and keypad codes, so the gate stops responding to everything but the hardwired open button. We reflash the board, reprogram the codes, and add a small surge protector at the board’s power input so the problem doesn’t return with the next thunderstorm.
• FAAC photocell faults that are actually wiring, not the photo-eye itself. On 400-series operators, a “photocell fault” on the display often points to a nicked low-voltage wire run from the gate to the photo-eye, not a failed sensor. In Irving’s clay-heavy soil, conduit shifts over time and the 24V wire inside gets abraded. We ring out the circuit with a meter, find the break, and repair the wire run rather than selling you a new photo-eye that wouldn’t solve anything.
• Keypad membrane wear on FAAC 412 and DigiKey units. After four or five Texas summers, the membrane buttons on FAAC keypads crack and stop making contact. The keypad housing looks fine from the outside. We replace the keypad with a FAAC-compatible unit and seal the new one with a UV-protective gasket, which buys you a couple extra seasons in direct sun.
• Radio receiver drift on older FAAC RP-series receivers. The RP-2 and RP-3 receivers used on many Irving FAAC gates from the early 2010s drift off frequency over time. Remotes that worked for years suddenly need to be held against the gate. We test the receiver’s actual output with a field-strength meter, and if it’s drifted past spec, we swap in a current FAAC receiver and pair your existing remotes to it.
• Phone-entry and intercom systems wired into FAAC open-relay terminals incorrectly. We see a lot of Irving gates where a phone entry system was added by a general contractor who didn’t understand FAAC’s normally-open vs. normally-closed terminal layout. The gate opens fine from the house but not from a call-in. We re-terminate the relay wires to the correct FAAC board inputs, test every access method, and leave you a wiring diagram of the corrected setup.

Our FAAC Gate Access Control Process

Every FAAC access-control job follows the same documented sequence, from the first call to the final test:

1. 1
   You call (817) 510-4183. A live person answers, asks what the gate is doing and what FAAC equipment you have, and sets a dispatch time. No voicemail loop, no callback queue.
2. 2
   We diagnose the exact failure. The technician meters the low-voltage circuit, checks the board for stored fault codes, and tests each access method individually: keypad, remote, phone entry, card reader, intercom. You get a written diagnosis with the specific fault named.
3. 3
   You approve a written price. Before any work starts, you get a flat number in writing under Haven Standard Clause 1. The price you approve is the price you pay. No hourly billing surprises.
4. 4
   We make the repair with the right parts. Where FAAC OEM parts make sense for warranty-safe longevity, we use them. Where a quality aftermarket receiver or keypad matches the original spec at half the cost, we tell you and let you decide.
5. 5
   We test every access point twice. The gate gets cycled on keypad, remote, phone entry, and any other access method at least twice each, with the safety edges and photo-eyes verified on every cycle.
6. 6
   You get the documentation before we leave. A photo log of what was found, what was set, and what was installed, plus a written record of the part number and the new settings. Clause 4, Evidence on every job.

Before

After

What FAAC Gate Access Control Costs in Irving

Here are the real numbers for FAAC access-control work in Irving based on what we’re quoting week to week, with the understanding that your exact number depends on the model and the wiring condition:

• Keypad replacement (FAAC 412 or compatible): $185-$340 installed, including programming and weather sealing.
• Faulty receiver swap (RP-series or newer): $210-$380 including pairing your existing remotes.
• Low-voltage wire run repair (underground break): $240-$520 depending on the length of conduit we need to pull and whether we’re trenching or using existing conduit.
• Control board repair or replacement (E024U or 400-series): $380-$620 for a rebuilt board with programming; new OEM boards run higher and we’ll quote the difference before ordering.
• Phone entry or video intercom integration into a FAAC board: $280-$550 for the relay wiring, programming, and testing of all access methods.

What moves the price most is the condition of the wiring. FAAC operators are durable; the low-voltage wiring in Irving’s shifting clay is not. You’ll always know the number before we start. Estimates are free, and we’ll review any other company’s written quote at no cost.

Why Irving Homeowners Call Vance Gate Repair Irving for FAAC Work

We’ve been doing this since 2014, and Adrian Vance started on commercial access-control sites where a wiring diagram and a written record were non-negotiable. That habit carried into every residential gate we touch in Irving. You get a technician who can name the FAAC board by sight, who meters the circuit instead of guessing, and who leaves you a photo log of what was adjusted and what part number was installed.

Every FAAC repair we complete is covered by the 365-Day Done Right Promise: if the repair isn’t right within one year, we make it right at no charge. And if your FAAC system ever needs to interface with another brand’s motor or receiver, we service the other major gate-automation brands too: LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. One company, whatever is already on the property.

FAQs